Subject:
|
Re: Factory Pictures Finally - Explanation of Curved roof
|
Newsgroups:
|
lugnet.town
|
Date:
|
Wed, 25 Jul 2001 15:19:43 GMT
|
Viewed:
|
392 times
|
| |
|
|
In lugnet.off-topic.debate, Jason Spears writes:
> In lugnet.off-topic.debate, Jesse Alan Long writes:
> > How DID you curve the roof of your factory/warehouse?
>
> > simply add some smokestacks and some of those yellow
> > and black striped LEGO plates, please?
>
> > Jesse Long
>
> Jesse I will take your 'demand'? of yellow and black striped tiles as a
> suggestion, and consider it when I get around the finishing the details. Thank
> you for the suggestion. But as far as smokestacks go, I have been to a number
> of manufacturing plants in my work, and I don't think it is needed nor
> explainable, as nothing in this little GoKart factory would warrent such an
> unsightly thing. Although you have now give me the idea for a processing plant
> with large smokestacks and soot everywhere, might be an interesting little
> building.
>
> As far as construction of the curved roof goes, it was a bit of a chore, I'll
> tell you. Others may have done it before and wouldn't find it a challange, but
> I found it tricky. The roof is composed of 6 large grey baseplates in a 2x3
> pattern. I used 2x8, 2x10 and 4x4 plates to connect the longest seem. You can
> see the pattern in this picture:
>
> http://www.brickshelf.com/cgi-bin/gallery.cgi?i=57102
I have seen this style of roof before:
http://www.wilkesworld.co.uk/lego/metro_terminus.htm
Scott A
>
> Then using 2x4 and 2x3 plates, I cover the other 4 seems. These smaller plates
> will allow the roof to bend without poping the plates off. The next part is a
> little tricky. When I put the roof on, I found it best to set the middle down
> on the peaks of the curves, seen here:
>
> http://www.brickshelf.com/cgi-bin/gallery.cgi?i=57106
>
> Then allow the long ends to bend. It will occasionaly want to bend into the
> building instead of to the walls, but once you get it bent in the right
> direction it is pretty easy. I built the wall with a lip that it can rest on
> and most of the force then goes out and not down. Finally I used 2x6 to keep
> the roof from popping up, which it does once in a while. Oh and here is a
> picture of me holding the roof right before I put it on Saturday.
>
> http://www.brickshelf.com/cgi-bin/gallery.cgi?i=57601
>
> Over the night with the plastic sheet over it, It buckeled and became less of a
> curve and more of a point. By design or mistake the roof is kind of strong, you
> can actually pull it (slide it) from one end or another to expose part of
> interior space. And some of you saw you can place some stuff on the roof, as
> seen in this picture:
>
> http://www.brickshelf.com/cgi-bin/gallery.cgi?i=58547
>
> The table wasn't very flat in that area, and since the factory splits into 6
> sections, connected with technic pegs, it kept cracking in that area. So after
> reconnecting the bricks in that area half a dozen times I decided it was best
> to make the crack look like it was by design. Hence the minifig repair crew.
>
> Well I hope I was clear in describing the roof. Enjoy and play well.
> Jason
|
|
Message has 1 Reply:
 | | Re: Factory Pictures Finally - Explanation of Curved roof
|
| (...) <snip> (...) but (...) can (...) Yep, I remember seeing that one too. Very cool building. I pretty sure it was more of a challange than mine. With the technic and windows below the curve. That was one of the main reasons why I even tried to (...) (23 years ago, 26-Jul-01, to lugnet.town)
|
Message is in Reply To:
5 Messages in This Thread:
  
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
This Message and its Replies on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|
