 | | RE: Six bladed propeller, all in line - no problem
|
|
(...) I've noticed that 1x plates attached to the holes of a 6 hole pulley don't move around very much. So to make a propellor, (with 3 blades offset by one or two plates), attach 3 1x plates to a pulley so they stick straight out. Do the same on (...) (25 years ago, 22-Sep-00, to lugnet.technic)
|
| |
| | Re: Six bladed propeller, pls help.
|
|
(...) cone such as the yellow one found on the exhaust (?) of the 8860 supercar could make a good spinner as well - although it would be better in black or grey, of course. Jennifer Clark (25 years ago, 22-Sep-00, to lugnet.technic)
|
| |
| | Re: Six bladed propeller, pls help.
|
|
(...) No no... It's built from the basic parts like 6-hole small technic pulleys, 1/2 pins and regular plates. This simple design dated from early 1980's, there was no such propellers exist at that time. Look at the picture (URL) for a fuzzy and (...) (25 years ago, 22-Sep-00, to lugnet.technic)
|
| |
| | Re: new LEGO elements (inside the Technic Powerpacks)
|
|
Hi Christian --- xTI@N. thanks for your scans! That gives a good view on the service packs. I will go for the styling- and the pneumatic-set! Keep on bricking! Kind regards, Holger (25 years ago, 22-Sep-00, to lugnet.technic, lugnet.general)
|
| |
| | Re: Six bladed propeller, all in line - no problem
|
|
(...) Et voila indeed! Hope I had the eight 3 blade rotors needed, do they come in black? I have to see if I can find a good source for them. Se my other answer in the original thread for my latest idea. Thanks! TGIF! /Tobbe (25 years ago, 22-Sep-00, to lugnet.technic)
|
| |
| | Re: Six bladed propeller, pls help.
|
|
Thanks all! I'll answer you one by one. Geoffrey, I'm not quite sure I understand what you mean *blush*. Are you refering to the 1x4 plate with a hole in each end with "notches" around the hole and some half-bushings? This solution would make the (...) (25 years ago, 22-Sep-00, to lugnet.technic)
|
| |
| | Re: Lego Mindstorms in Swedish television
|
|
(...) Or for every one, here is the official page from the University: (URL) and drool :) TGIF! /Tobbe (25 years ago, 22-Sep-00, to lugnet.loc.se, lugnet.general, lugnet.robotics, lugnet.technic)
|
| |
| | Re: transmision help... Anyone?
|
|
(...) make (...) 8448. (...) Or here: (URL) 15 & 16. ROSCO (25 years ago, 22-Sep-00, to lugnet.technic)
|
| |
| | Re: transmision help... Anyone?
|
|
(...) make (...) 8448. (...) THanks, now I'm going to attempt at making a car similar to those driven at le mans and sebring, going to be a bit hard with my biggest set being the Indy storm. THanks Geordan (25 years ago, 22-Sep-00, to lugnet.technic)
|
| |
| | Re: transmision help... Anyone?
|
|
(...) ratios both between input and sliding axle and between sliding axle and output, it is relatively easy to increase the number of speeds - though at some point, one will need an axle connector in the rather long slding axle. I've gotten up to (...) (25 years ago, 21-Sep-00, to lugnet.technic)
|
