|
|
 | | Brickfest 2005 USA
|
| Who all is going to brickfest in the US? Lord willing I will be there with all my construction equipment completed and on display. I am want to go not just to display my creations but to meet other lego builders that I have talked to on the net. (...) (19 years ago, 22-Jun-05, to lugnet.technic)
| | | | | Re: tougher lego gears
|
| (...) I don't think the plastic-glue bond would have to be stronger than plastic with itself. I'm just talking about filling up the hole so that the gear won't crack as easily at the thin points next to the holes. This is where the breaks are always (...) (19 years ago, 22-Jun-05, to lugnet.parts.custom, lugnet.parts.mod, lugnet.technic)
| | | | | Re: tougher lego gears
|
| (...) If the material is failing, I doubt filling the holes will help (perhaps, *maybe*, with a very strong glue, but I still doubt it). The problem is getting anything to bond the plastic nearly as strongly as the plastic bonds to itself. I don't (...) (19 years ago, 22-Jun-05, to lugnet.parts.custom, lugnet.parts.mod, lugnet.technic)
| | | | | Re: tougher lego gears
|
| (...) This time I heated it for 10 minutes and let it cool in tap water for a fair while. The gear lasted noticeably longer - almost to the end (it's operating a elastic wind-back mechanism). But then it snapped. The gears always crack at the (...) (19 years ago, 22-Jun-05, to lugnet.parts.custom, lugnet.parts.mod, lugnet.technic)
| | | | | Re: tougher lego gears
|
| (...) Dope another one. This time cool it with tap water, not iced water. You may have cooled it too fast, if I understand that thread correctly. Keith (19 years ago, 21-Jun-05, to lugnet.parts.custom, lugnet.parts.mod, lugnet.technic)
| | | | | Re: tougher lego gears
|
| (...) Bummer. My suggestion would be to "gang" more gears side-by-side. You could use metal gears, like meccano or something, but you'd always have a weak point at the plastic/metal interface. Or you could do all the mechanicals in metal, and just (...) (19 years ago, 21-Jun-05, to lugnet.parts.custom, lugnet.parts.mod, lugnet.technic)
| | | | | Re: tougher lego gears
|
| (...) I "doped" the gear and it still broke. I think it might have lasted a bit longer though. I put it in boiling water for 5 minutes then in iced water for 5 minutes. Didn't use it until about 15 minutes later. Any other suggestions? Jack (19 years ago, 21-Jun-05, to lugnet.parts.custom, lugnet.parts.mod, lugnet.technic)
| | | | | Re: tougher lego gears
|
| (...) Take a look at this: (URL) - David (19 years ago, 20-Jun-05, to lugnet.parts.custom, lugnet.parts.mod, lugnet.technic)
| | | | | Re: 8421 first impressions
|
| (...) I like the smaller lift & carry cranes, which actually run the hoist cable through the boom extension, so that extending the boom doesn't require letting out any cable at all. (...) That may be a playability decision. As I found with my (URL) (...) (19 years ago, 19-Jun-05, to lugnet.technic, FTX)
| | | | | Re: 8421 first impressions
|
| (...) I also have finished this set and I also like the boom extension, but the main problems for me seem to be that the boom extension doesn't move smoothly, and the outriggers follow the same pattern as the ones from earlier sets (8862, 8460). (...) (19 years ago, 19-Jun-05, to lugnet.technic)
|
|
