 | | Re: Differences between Raw Sensor readings and Light Sensor
|
|
(...) I'd guess it depends on what you are doing. Without a doubt, raw gives you the best sensor resolution. I'd guess that for kids it is easier to think in terms of 0 to 100%. Since you are not a kid, raw is probably better. (...) Kevin (21 years ago, 15-Apr-04, to lugnet.robotics.rcx)
|
| |
| | Differences between Raw Sensor readings and Light Sensor
|
|
Hi, Can someone point out the differences between setting a sensor as Light (or any custom sensor) vs setting the sensor as Raw? Isnt it better to use the RAW readings since it reports a range of 0 to 1023 as opposed to scaling the readings to 0 to (...) (21 years ago, 14-Apr-04, to lugnet.robotics.rcx)
|
| |
| | Re: BricxCC & downloading NQC programs failing
|
|
Hi, (...) do you have any idea what the write timeout does and is needed for? I'm wondering whether I would need that in the Linux driver, currently I only have the other two. Jürgen (21 years ago, 11-Apr-04, to lugnet.robotics, lugnet.robotics.rcx, lugnet.robotics.rcx.nqc)
|
| |
| | BricxCC & downloading NQC programs failing
|
|
I have heard from a user of BricxCC who has been experiencing the "compile failed: no (or bad) reply from RCX" (or words to that effect) error message when trying to download pretty much any NQC program either using BricxCC or using NQC directly (...) (21 years ago, 11-Apr-04, to lugnet.robotics, lugnet.robotics.rcx, lugnet.robotics.rcx.nqc)
|
| |
| | IR to RF conversion for the RCX
|
|
Hi, As I was searching for ways to remove the "line-of-sight" problem with the RCX, I ran across this link: (URL) guys are building a complete RF module for the RCX. They are replacing the tower with a RS232-RF tower and they are also building a (...) (21 years ago, 8-Apr-04, to lugnet.robotics.rcx)
|
| |
| | Re: New Sensor - ADXRS300-based Gyro for the RCX
|
|
(...) I fixed it right after I posted. Sorry about that.... Cheers, Ram (21 years ago, 6-Apr-04, to lugnet.robotics.rcx)
|
| |
| | Re: New Sensor - ADXRS300-based Gyro for the RCX
|
|
(...) Forgot to mention that now I am ready to tackle Legway using the ADXRS300 Gyro, ADXL202 Accelerometer, and a bit of Kalman filtering. Watch out Steve, I am coming ;-) Steve, you did an AMAZING JOB on LegWay!!!.... Cheers, Ram (21 years ago, 6-Apr-04, to lugnet.robotics.rcx)
|
| |
| | Re: New Sensor - ADXRS300-based Gyro for the RCX
|
|
(...) ROSCO (21 years ago, 6-Apr-04, to lugnet.robotics.rcx)
|
| |
| | New Sensor - ADXRS300-based Gyro for the RCX
|
|
Hi, Here is my prototype Analog Devices-based ADXRS300 Gyroscope sensor for the RCX. Check it out at: (URL) (21 years ago, 6-Apr-04, to lugnet.robotics.rcx)
|
| |
| | Re: Mounting PCB boards inside a lego brick
|
|
(...) Is that stuff non-conductive? Ram (21 years ago, 1-Apr-04, to lugnet.robotics.rcx)
|
