 | | Re: I'm passing the NQC torch...
|
|
A few hours after I was working with my brand new RIS kit, I knew the programming environment was too limited for my needs. Thanks God there was NQC out there, very young but already very solid, offering an entire new world of possibilities. Without (...) (21 years ago, 12-Nov-03, to lugnet.robotics.rcx.nqc)
|
| |
| | Motors on Sensor ports
|
|
I'm just curious if there's any harm in connecting motors to active sensor ports... I know you don't get very much voltage/speed/torque, but you do get interesting readings that can be used to detect when the motor stalls. This is potentially a very (...) (21 years ago, 12-Nov-03, to lugnet.robotics.rcx)
|
| |
| | Re: Help w/install _or_ It all went so well
|
|
(...) [...] (...) Well it looks like the gcc-version-problem I had. The gcc >=3.x do not allow multiline strins without "\" anymore, which are still uses in brickos. So my hint is to install a gcc 2.95 and everything should work fine... Note: This (...) (21 years ago, 12-Nov-03, to lugnet.robotics.rcx.legos)
|
| |
| | Help w/install _or_ It all went so well
|
|
_warning_ I'm new to BrickOS, so be patient. I've just attempted to install using the instructions at (URL) went fine until step 4 command './configure; make' which looked like this: ... $ ./configure; make Welcome to the brickOS Makefile (...) (21 years ago, 12-Nov-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: I'm passing the NQC torch...
|
|
Dear Dave, All I can Say is Thanks. But that says it all. JL (21 years ago, 11-Nov-03, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: ROM image using USB tower
|
|
(...) Andrew, I grabbed a ROM image awhile back using a serial tower and an RCX 1.0. I haven't tried this on a 2.0 brick, but I think the ROMware is identical in all RCX versions. Although Kekoa's SEND.C uses the serial tower, it is not too hard to (...) (21 years ago, 12-Nov-03, to lugnet.robotics.rcx)
|
| |
| | Re: I'm passing the NQC torch...
|
|
(...) Dave, please allow me to add my name to the list of appreciative fans of your work, and the generous example you put forward to the LEGO/Mindstorms community. We all owe you a lot! -- Russ (21 years ago, 11-Nov-03, to lugnet.robotics.rcx.nqc)
|
| |
| | ROM image using USB tower
|
|
Hi, I'm doing a project at University involving developing some example programs running on a Lego RCX in order to demonstrate/teach OS concepts. I'd really like to get hold of a ROM image from the RCX, but I only have a USB tower available, and (...) (21 years ago, 12-Nov-03, to lugnet.robotics.rcx)
|
| |
| | Re: I'm passing the NQC torch...
|
|
(...) Please allow me add my sincere thanks to Dave for all the hard work he has put in over the last few years. As far as I am concerned, RIS only really appeals to me because of the access that NQC has permitted to the RCX. Were we to have been (...) (21 years ago, 11-Nov-03, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: I'm passing the NQC torch...
|
|
(...) Dave, Thanks so much for the work you have put into NQC. I have used this tool exclusively with BricxCC. You have changed the face of Mindstorms programming and for that I and I am sure many others are grateful. Thanks again, Dave (21 years ago, 11-Nov-03, to lugnet.robotics.rcx.nqc)
|
