 | | Re: NQC tutorial available
|
|
Excellent Job Mark. Thanks for all of your hard work. -Phil (...) (26 years ago, 29-Mar-99, to lugnet.robotics.rcx.nqc, lugnet.robotics)
|
| |
| | Uploading *.prg To RCX
|
|
Is there a program that allows you to download the prg files created from the Lego CD-ROM to the RCX without loading the Lego CD program? Help Appreciated! Adamski _______ <adamski2000@adamski...rve.co.uk> (26 years ago, 28-Mar-99, to lugnet.robotics, lugnet.robotics.rcx.legos)
|
| |
| | Re: NQC tutorial available
|
|
(...) Mark, I use your NQCCC exclusively to program my RCX. Your code templates and help system (especially the last edition!) are superb. I like your setup because it integrates all the necessary stuff right there and the help files are pretty good (...) (26 years ago, 29-Mar-99, to lugnet.robotics.rcx.nqc, lugnet.robotics)
|
| |
| | NQC tutorial available
|
|
In my opinion NQC is the easiest way to program the Lego Robots. But people that never programmed before seem to think it is difficult (maybe because it sounds like C). So I decided to write an extensive tutorial on how to use NQC. The tutorial does (...) (26 years ago, 29-Mar-99, to lugnet.robotics.rcx.nqc, lugnet.robotics)
|
| |
| | legOS Network Protocol
|
|
Markus, I have been away for the last week or so. What have I missed in the discussion on LNP? I would like to get cracking on this. I have 2 or 3 guys over here who want to get into this too. -Jake Jacob S. Barrett jsbarrett@acm.org (26 years ago, 28-Mar-99, to lugnet.robotics.rcx.legos)
|
| |
| | Light Sensor Non Destructive Mods
|
|
Hi All, I've just added a new page to my website that describes a non-destructive mod to the light sensor that actually allows it to read ambient light! (URL) The range is <10 for a dark box and >90 for a halogen lamp about 6 feet away. It's really (...) (26 years ago, 28-Mar-99, to lugnet.robotics, lugnet.robotics.rcx.pbforth)
|
| |
| | RE: Why do it? Was: multi-device output controller
|
|
(...) Measuring PWM is not difficult, but it would involve a micro (PIC12C508 anyone?) dedicated to the task and then you would have to get it to drive the RCX, which means motor drivers, etc. If you are willing to spend $50 and LOTS of time, then (...) (26 years ago, 27-Mar-99, to lugnet.robotics, lugnet.robotics.rcx.pbforth)
|
| |
| | Re: Why do it? Was: multi-device output controller
|
|
Ralph, Thanks for reigning in the rabbit chase! As the originator of this thread I'd like to respond to the 'why'... I keep running out of ports on my creations. I see 5 or 6 as a practical limit. My criteria for a solution: 1. Entirely compliant (...) (26 years ago, 26-Mar-99, to lugnet.robotics, lugnet.robotics.rcx.pbforth)
|
| |
| | Why do it? Was: multi-device output controller
|
|
(...) I have checked this out, and if you use the standard RCX firmware (or other firmware that uses the RCX ROM, then you get the waveforms you are talking about at 125Hz 1/(1ms x 8). You also get polarity information - oh no, I've said too much. (...) (26 years ago, 26-Mar-99, to lugnet.robotics, lugnet.robotics.rcx.pbforth)
|
| |
| | Re: gcc build instructions for linux
|
|
(...) week ago. (26 years ago, 26-Mar-99, to lugnet.robotics.rcx.legos)
|
