 | | Re: NXT Robot Swarm at BrickFest -- featuring Bluetooth
|
|
(...) My problems with this solution are two-fold. First, NXT-G currently can't send anything back to the PC, as it's not running anything to get the NXT-G message structure (yes, folks could write this... almost certainly will. But likely not me). (...) (18 years ago, 13-Aug-06, to lugnet.robotics.nxt)
|
| |
| | Re: NXT Robot Swarm at BrickFest -- featuring Bluetooth
|
|
Here's an idea of how to get more than 3 NXTs connected via Bluetooth (BT). It involves using a PC as a "relay point". I think standards allow up to seven simultaneous connections per BT device. The limitation to three connections on the NXT may be (...) (18 years ago, 13-Aug-06, to lugnet.robotics.nxt)
|
| |
| | Re: NXT Motor Encoder Accuracy and Dead Reckoning
|
|
(...) I've played with it a good bit. It seems to be extremely accurate, in that one motor will slavishly follow the other - you can do demos like set a Move block to drive forward 10 rotations, and while it's trying to do that pick up the robot and (...) (18 years ago, 13-Aug-06, to lugnet.robotics.nxt)
|
| |
| | Re: NXT Motor Encoder Accuracy and Dead Reckoning
|
|
Dick, the article you referenced with the PID controller is excellent. I spent a lot of time trying to do a straight line with an RCX model a few years ago, but with a different approach: It was track-driven and the drive shaft extension on each (...) (18 years ago, 13-Aug-06, to lugnet.robotics.nxt)
|
| |
| | NXT Motor Encoder Accuracy and Dead Reckoning
|
|
Has anyone done any experiments on the accuracy of the NXT motor "move to" block? If so, can they post their results or impressions? I know NXT supports PID calculations to synchronize two motors and run in a straight line. Can you use this to drive (...) (18 years ago, 13-Aug-06, to lugnet.robotics.nxt)
|
| |
| | Re: NXT Robot Swarm at BrickFest -- featuring Bluetooth
|
|
(...) I played around with this a little bit, trying to confirm what I've been told. It is possible to have an NXT connect as either a master or a slave, but not both at the same time. I'm sure this is true. Here's what I did: I took three NXTs with (...) (18 years ago, 13-Aug-06, to lugnet.robotics.nxt)
|
| |
| | Re: NXT Robot Swarm at BrickFest -- featuring Bluetooth
|
|
(...) As I was working on my ruby-nxt module, I managed to get the nxt to connect to my laptop as both a master and a slave. On my laptop (a MacBookPro) I created an incoming bluetooth serial port and an outgoing serial port on the DEV-B device (...) (18 years ago, 11-Aug-06, to lugnet.robotics.nxt)
|
| |
| | Re: NXT Robot Swarm at BrickFest -- featuring Bluetooth
|
|
(...) Jordan, I think swarming would be very fun to explore, but, for me, there isn't enough time before BF. Here's something you could play around with before BF: (URL) by getting your robot to follow the line on the test pad. To answer your (...) (18 years ago, 11-Aug-06, to lugnet.robotics.nxt, FTX)
|
| |
| | Re: NXT Robot Swarm at BrickFest -- featuring Bluetooth
|
|
It's good that people are interested! With the RCX couldn't you just have a robot broadcast a message to anything that could see the IR signal and was waiting for specific messages to arrive? Can a similar thing be done with BT? Would we be better (...) (18 years ago, 11-Aug-06, to lugnet.robotics.nxt, FTX)
|
| |
| | Re: Spike Building Guide Typo
|
|
(...) The same three girls got confused by the programming instructions for Spike "Reactions". They missed the proper placement of the second switch block within the primary switch block within the loop block in frame 8. Confused? So was I. They saw (...) (18 years ago, 11-Aug-06, to lugnet.robotics.nxt)
|
