 | | Re: NBC Control of RCX Sensors
|
|
Another observation. It seems that the IN_TYPE_LIGHT_INACTIVE is really not meant to be used with the RCX light sensor. There is very little sensitivity with this setting. The IN_TYPE_REFLECTION setting is much more sensitive. Too bad that we lost (...) (18 years ago, 2-Jan-07, to lugnet.robotics.nxt)
|
| |
| | Re: NBC Control of RCX Sensors
|
|
OK, I answered my own question. I just needed to set the sensor type to: IN_TYPE_LIGHT_INACTIVE for RCX light sensor with the LED ON IN_TYPE_REFLECTION for RCX light sensor with the LED OFF (18 years ago, 2-Jan-07, to lugnet.robotics.nxt)
|
| |
| | NBC Control of RCX Sensors
|
|
Has anyone tried to control the RCX sensors with NBC? I have the converter cable and hooked up my RCX light sensor, but only got back readings of 53 (percent full scale). I used the NBC SetSensorLight command which should set the sensor to turn on (...) (18 years ago, 2-Jan-07, to lugnet.robotics.nxt)
|
| |
| | Re: How to implement continuous drive with NXT motors?
|
|
I am not a NXT-G expert. I'm a programmer, so I moved to NBC pretty quickly. It's much easier for me to do things in a language than with graphics (not to mention the programs are 1/10 the size of NXT-G). Good Luck! David (18 years ago, 1-Jan-07, to lugnet.robotics.nxt)
|
| |
| | Re: How to implement continuous drive with NXT motors?
|
|
"David Wallace" <dww.robotics@gmail.com> skrev i en meddelelse news:JB3HDF.3EL@lugnet.com... (...) I suppose you have to make the change between drive direction blocks by means of some "until sensor actuated" block, then? This was my very first (...) (18 years ago, 1-Jan-07, to lugnet.robotics.nxt)
|
| |
| | Re: Connect BT devices to the NXT without a passkey?
|
|
In article <JAynn0.90L@lugnet.com>, Jordan Bradford <jordan_bradfordREMO VE_THIS_SPAM_THINGY@...tmail.com> writes (...) I have not tried this, but I would expect it to work. (...) Alas, this will not work. Bluetooth is just a means of carrying (...) (18 years ago, 31-Dec-06, to lugnet.robotics.nxt)
|
| |
| | Re: Sending program by bluetooth
|
|
Hi Jan, I had asked this question of John Hansen a while back. His response follows. Note that this reduced my connection time in BricxCC from 17 seconds to 3 seconds. "First use NeXTTool.exe to create a nxt.dat file like so: nexttool -listbricks > (...) (18 years ago, 30-Dec-06, to lugnet.robotics.nxt)
|
| |
| | Re: How to implement continuous drive with NXT motors?
|
|
Hi David, For the motor block, did you choose "Unlimited" in the "Duration" field dropdown box? It defaults to 1 "Rotation". David Wallace "David List" <zerobuttons@gmail.com> wrote in message news:JB3A0n.2MH@lugnet.com... (...) block (...) (18 years ago, 30-Dec-06, to lugnet.robotics.nxt)
|
| |
| | How to implement continuous drive with NXT motors?
|
|
Can anyone here help me get continuous drive with NXT motors? I am using NXT-G now, while getting a feel for Mindstorms NXT. I experience that I am unable to get continuous drive with the motors when shifting from one block to another. The speed (...) (18 years ago, 30-Dec-06, to lugnet.robotics.nxt)
|
| |
| | Sending program by bluetooth
|
|
Dear All, I send a program compiled (NBC) with the Bricx Command Center to my NXT with a Bluetooth connection. It takes a relative long time before my NXT is ready to run. Is this normal? Can I improve this time? Regards, Jan Kromhout (...) (18 years ago, 29-Dec-06, to lugnet.robotics.nxt)
|
