 | | Re: NXT Ultrasonic reporting wrong values
|
|
(...) I'm not sure what you mean by "completely stopped" - stationary? I suppose it's possible that you actually have a bad US sensor. If you can find someone with a working one, try swapping sensors with them and see if the problem is isolated to (...) (18 years ago, 15-Oct-06, to lugnet.robotics, lugnet.robotics.nxt)
|
| |
| | Re: NXT-G using RCX items.
|
|
----- Original Message ----- From: "Roger Glassey" <glassey@ieor.berkeley.edu> To: <lugnet.robotics.nxt...ugnet.com> Sent: Sunday, October 15, 2006 12:53 AM Subject: Re: NXT-G using RCX items. (...) Thanks for the infomation Roger. I'm going to (...) (18 years ago, 15-Oct-06, to lugnet.robotics.nxt)
|
| |
| | NXT Ultrasonic reporting wrong values
|
|
A just get my NXT, and everything works fine, but the ultrasonic sensor is not reporting correct values. No matter what distance or direction it is pointed, the readings changes quickly from 1 to 3 inches (3 to 7 cm) even if the sensor is completely (...) (18 years ago, 15-Oct-06, to lugnet.robotics, lugnet.robotics.nxt)
|
| |
| | Re: NXT-G using RCX items.
|
|
(...) I have a conveter cable so I finally did some tests with NXT-G and here is what I find-- RCX motor runs in both directions, and responds to the speed settings. The touch sensor works. The light sensor measures ambient light. But the bad news (...) (18 years ago, 15-Oct-06, to lugnet.robotics.nxt)
|
| |
| | Managing Memory
|
|
I've got 8 kids working on NXT who have been experiencing "not enough memory". So, I did a little experimenting. Every new program takes a minimum of 6K. Every Move Block takes 0.5K Imagine that! 500 bytes for a simple move block. I haven't measured (...) (18 years ago, 14-Oct-06, to lugnet.robotics.nxt)
|
| |
| | Re: NXT-G using RCX items.
|
|
(...) Well, you need converter cables of some sort to even connect RCX sensors and motors to the NXT. Beyond that, I'm not sure; I've not tried yet, because I don't have the converter cables to try. I suspect you will need the special NXT-G (...) (18 years ago, 13-Oct-06, to lugnet.robotics.nxt)
|
| |
| | NXT-G using RCX items.
|
|
Hello Everyone: I just read the press release regarding the LEGO Mindstorms Education NXT. There is no discount available for their software that allows me to use my RCX motors, sensors etc with the NXT-G. Do I even need their version to run RCX (...) (18 years ago, 13-Oct-06, to lugnet.robotics.nxt)
|
| |
| | Re: NXT to RCX Communications
|
|
----- Original Message ----- From: "Brian Davis" <brdavis@iusb.edu> To: <lugnet.robotics.nxt...ugnet.com> Sent: Wednesday, October 04, 2006 10:23 PM Subject: Re: NXT to RCX Communications (...) Thanks Brian. I might as well use the time to try and (...) (18 years ago, 5-Oct-06, to lugnet.robotics.nxt)
|
| |
| | Re: NXT to RCX Communications
|
|
(...) No. The light sensor can have the red LED either on or off - you can't set it to "20%" or something like that, and there's no way to toggle the LED fast enough to mimic or RCX-style IR message. But... You could cetainly have a program (...) (18 years ago, 5-Oct-06, to lugnet.robotics.nxt)
|
| |
| | NXT to RCX Communications
|
|
Hello everyone: Is it possible for the NXT to send Run Program commands from the NXT to RCX via a light sensor? Here is an example: 1- The NXT Ultrasound sensor detects an object close by, triggers the NXT light sensor to light up at 20 percent (...) (18 years ago, 5-Oct-06, to lugnet.robotics.nxt)
|
