 | | Re: nxt + i2c sp03 Text-To-Speech?
|
|
(...) I'd say its worth a try from the 4.3v supply from the NXT. I note that the SP03 spec. says it has a 3v regulator onboard, so its not really running from 5v anyhow. The I2C signals are open drain, so they should be ok unless their inputs won't (...) (18 years ago, 5-Dec-06, to lugnet.robotics.nxt)
|
| |
| | Re: nxt + i2c sp03 Text-To-Speech?
|
|
(...) It sounds like the NXT probably doesn't have enough power available to run that chip, but you might look at using a BUC (Boost-Up Converter) component to bring the 4.3V supply up to a higher level? I've only been peripherally involved with (...) (18 years ago, 5-Dec-06, to lugnet.robotics.nxt)
|
| |
| | Re: nxt + i2c sp03 Text-To-Speech?
|
|
(...) Yes, but unfortunately the 9V sensor supply is limited to 15mA just like the RCX sensor supply. Not easy to power a module that consumes 80mA... Philo (18 years ago, 5-Dec-06, to lugnet.robotics.nxt)
|
| |
| | Re: nxt + i2c sp03 Text-To-Speech?
|
|
(...) That would be the LOWSPEED_9V flag? (...) I just might do that. (...) The chip used in the book I have is the SpeakJet (URL) It's a LOT cheaper than the sp03, however, it uses a serial interface and would be a lot more complicated. I'd have to (...) (18 years ago, 5-Dec-06, to lugnet.robotics.nxt)
|
| |
| | RE: nxt + i2c sp03 Text-To-Speech?
|
|
The NXT can also optionally apply 9V to I2C sensors on the same input/wire that is used for reading the analog values. There's a flag to set this up. I know it is accessible in RobotC and I think you should also be able to set it up via NBC. SO (...) (18 years ago, 5-Dec-06, to lugnet.robotics.nxt)
|
| |
| | Re: nxt + i2c sp03 Text-To-Speech?
|
|
Hi Tony, (...) Nice little beast! (...) Most probably it should work. I am a bit more concerned about current consumption (80mA - not 80mAH as shown in documentation!), since the 4.3V supply can deliver 180mA for ALL seven NXT ports. You may also (...) (18 years ago, 5-Dec-06, to lugnet.robotics.nxt)
|
| |
| | nxt + i2c sp03 Text-To-Speech?
|
|
I'm a software guy, not a hardware guy. I have very little experience designing circuits. To show how little I know, I'm actually reading through Electronics Projects for Dummies at the moment. ;) Well in this book they describe a simple (...) (18 years ago, 5-Dec-06, to lugnet.robotics.nxt)
|
| |
| | Re: NBC-NCX Experiences
|
|
(...) The simple answer is that NXC does not yet expose that functionality. I am feverishly working on implementing that API. I apologize for the compiler problems. John Hansen (18 years ago, 3-Dec-06, to lugnet.robotics.nxt)
|
| |
| | NBC-NCX Experiences
|
|
Hello NXT-Community, currently I make some tests with the very nice NBC-NXC compiler. My first tries to drive the Tribot around were successfully 8-) But now my question is: How can I access sensors from NXC ? All my attempts causes the compiler to (...) (18 years ago, 2-Dec-06, to lugnet.robotics.nxt)
|
| |
| | NBC Debugger
|
|
Tamas Sorosy has recently made his awesome NBC Debugger available via his website. (URL) this page you will find a link to the NBC Debugger as well as his excellent NBC math library. To use the debugger you should download the very latest test (...) (18 years ago, 1-Dec-06, to lugnet.robotics.nxt)
|
