 | | Re: HandyBoard Assembly Problems
|
|
Matt: It sounds like maybe you have a DS1233M instead of a DS12323. The "M" part is a replacement for the MC34064 and has a different pinout than the regular DS1233. I have both versions, DS1233 for the Handy Board and DS1233M for the Finger Board. (...) (25 years ago, 26-May-99, to lugnet.robotics.handyboard)
|
| |
| | HandyBoard Assembly Problems
|
|
Hi all, I'm at stage 4.2.1 of assembling my Handyboard(v1.2) Where you install U12, the DS1233 3-pin ic. And it doesn't work, I've worked through the debugging stage, Led11R IS in the right way round, and I've tried U12 both ways. What happens is (...) (25 years ago, 25-May-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Using SPI
|
|
(...) Dear Carlos, I will make it available. I have managed to improve on the code so I have better control, but have a way to go yet before it is finish. So far, I am able to send data reliably at 62,500 bits per second without interrupts. I expect (...) (25 years ago, 24-May-99, to lugnet.robotics.handyboard)
|
| |
| | Sound algorithms
|
|
Christopher Prosser's question about MIDI started me thinking about adding some sound effects from the speaker. I know the capabilities of the on-board sound are limited, but has anyone done any work on simple sound effects (splat, boing, au-oh, (...) (25 years ago, 24-May-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Using SPI
|
|
(...) Gary, We used the PA7(transmitting board) and PD0(receiving board) in wireless and wired mode. This is quite easy to do. Pete Eacmen have done the wired stuff while I did the wireless stuff. With wired one, you can transmit @9600 baud with no (...) (25 years ago, 23-May-99, to lugnet.robotics.handyboard)
|
| |
| | Sony Robotic Dog URL correction
|
|
I misquoted the URL. Typed so fast, I left out the world wide web prefix. It should read: (URL) Tonkens (25 years ago, 23-May-99, to lugnet.robotics.handyboard)
|
| |
| | Sony Robotic Dog: Check it Out!
|
|
(URL) dog is wild! It can learn behaviors and it can be reprogrammed! Ross M. Tonkens, M.D. Medical Director Primary Care of Nevada 100 North Green Valley Parkway Suite 240 Henderson, NV 89014 702 914-7120 VOICE 702 914-7129 FAX (25 years ago, 23-May-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Midi?
|
|
(...) Chris, check: (URL) is a midi library for the Hb here. Best, Duncan (25 years ago, 23-May-99, to lugnet.robotics.handyboard)
|
| |
| | Midi?
|
|
Hi Folks, I was wondering if anyone had any code to input/output Midi from the Handyboard? Thanks, Chris Prosser (25 years ago, 23-May-99, to lugnet.robotics.handyboard)
|
| |
| | Using SPI
|
|
I am using the SPI port to communicate with another Handy Board. I have written a routine in IC that will pass bytes between controllers just as it is supposed to work. However, the code is not very clean and it is very touchy. Change one thing and (...) (25 years ago, 22-May-99, to lugnet.robotics.handyboard)
|
| |
| | L.A. Store
|
|
Hi Does anybody know about a electronic or robotic store at L.A. (Los Angeles).? And the Address. Please Thanks Daniel ---...--- " `BETTER´ IS THE ENEMY OF `GOOD ENOUGH´" ---...--- (25 years ago, 22-May-99, to lugnet.robotics.handyboard)
|
| |
| | RE: withdraw?
|
|
I'm not sure how "signatures" work, but maybe one could be added to every handyboard message reminding people of the proper procedure on how to take themselves off the mailing list? Just a suggestion! Dave (25 years ago, 22-May-99, to lugnet.robotics.handyboard)
|
| |
| | withdraw
|
|
Dear Sir, Please take from the list. Thanks for all, Jorge (25 years ago, 22-May-99, to lugnet.robotics.handyboard)
|
| |
| | Re: External Motor Power Problems
|
|
At 08:50 PM 5/21/99 -0700, Bill Denzel wrote: What (...) Looking at the schematic for the motor driver circuit at: (URL) the 'HC04 and the '374 are implicated. Do all the other functions of the HB work? Duncan (25 years ago, 22-May-99, to lugnet.robotics.handyboard)
|
| |
| | External Motor Power Problems
|
|
Hello all, I modified my HB to except the external motor source. After downloading a test program to see if all the ports worked, I found that only one motor port now works. There is the possibility that I shorted out other chips, but I am sure that (...) (25 years ago, 22-May-99, to lugnet.robotics.handyboard)
|
| |
| | withdraw
|
|
Dear Sir, I don;t wished to be in the list anymore. Thanks ! Rgds, Linnar (25 years ago, 22-May-99, to lugnet.robotics.handyboard)
|
| |
| | L.A. Store
|
|
Hi Does anybody know about a electronic or robotic store at L.A. (Los Angeles).? And the Address. Please Thanks Daniel ---...--- " `BETTER´ IS THE ENEMY OF `GOOD ENOUGH´" ---...--- (25 years ago, 22-May-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Handyboard/Miniboard Replacement
|
|
Why would you get flamed? it's just a conformal coating. they do it a lot in the military. It *IS* possible to fix a circuit board that's been protected in this way; when I was in the Navy one of the schools I went to was in microminiature (...) (25 years ago, 21-May-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Handyboard/Miniboard Replacement
|
|
(...) I'll get flamed for this, but I once dipped a board for an underwater robot in that liquid plastic stuff. It's at hardware stores, used for dipping wrench handles and stuff to make them more comfortable and electrically insulated. I held the (...) (25 years ago, 21-May-99, to lugnet.robotics.handyboard)
|
| |
| | Re: L.A. Store
|
|
Nope, That's in Norther California... Just a quick 6 hour drive though :-) --Mike (...) (25 years ago, 21-May-99, to lugnet.robotics.handyboard)
|
