 | | Sony Robotic Dog URL correction
|
|
I misquoted the URL. Typed so fast, I left out the world wide web prefix. It should read: (URL) Tonkens (25 years ago, 23-May-99, to lugnet.robotics.handyboard)
|
| |
| | Sony Robotic Dog: Check it Out!
|
|
(URL) dog is wild! It can learn behaviors and it can be reprogrammed! Ross M. Tonkens, M.D. Medical Director Primary Care of Nevada 100 North Green Valley Parkway Suite 240 Henderson, NV 89014 702 914-7120 VOICE 702 914-7129 FAX (25 years ago, 23-May-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Midi?
|
|
(...) Chris, check: (URL) is a midi library for the Hb here. Best, Duncan (25 years ago, 23-May-99, to lugnet.robotics.handyboard)
|
| |
| | Midi?
|
|
Hi Folks, I was wondering if anyone had any code to input/output Midi from the Handyboard? Thanks, Chris Prosser (25 years ago, 23-May-99, to lugnet.robotics.handyboard)
|
| |
| | Using SPI
|
|
I am using the SPI port to communicate with another Handy Board. I have written a routine in IC that will pass bytes between controllers just as it is supposed to work. However, the code is not very clean and it is very touchy. Change one thing and (...) (25 years ago, 22-May-99, to lugnet.robotics.handyboard)
|
| |
| | L.A. Store
|
|
Hi Does anybody know about a electronic or robotic store at L.A. (Los Angeles).? And the Address. Please Thanks Daniel ---...--- " `BETTER´ IS THE ENEMY OF `GOOD ENOUGH´" ---...--- (25 years ago, 22-May-99, to lugnet.robotics.handyboard)
|
| |
| | RE: withdraw?
|
|
I'm not sure how "signatures" work, but maybe one could be added to every handyboard message reminding people of the proper procedure on how to take themselves off the mailing list? Just a suggestion! Dave (25 years ago, 22-May-99, to lugnet.robotics.handyboard)
|
| |
| | withdraw
|
|
Dear Sir, Please take from the list. Thanks for all, Jorge (25 years ago, 22-May-99, to lugnet.robotics.handyboard)
|
| |
| | Re: External Motor Power Problems
|
|
At 08:50 PM 5/21/99 -0700, Bill Denzel wrote: What (...) Looking at the schematic for the motor driver circuit at: (URL) the 'HC04 and the '374 are implicated. Do all the other functions of the HB work? Duncan (25 years ago, 22-May-99, to lugnet.robotics.handyboard)
|
| |
| | External Motor Power Problems
|
|
Hello all, I modified my HB to except the external motor source. After downloading a test program to see if all the ports worked, I found that only one motor port now works. There is the possibility that I shorted out other chips, but I am sure that (...) (25 years ago, 22-May-99, to lugnet.robotics.handyboard)
|
| |
| | withdraw
|
|
Dear Sir, I don;t wished to be in the list anymore. Thanks ! Rgds, Linnar (25 years ago, 22-May-99, to lugnet.robotics.handyboard)
|
| |
| | L.A. Store
|
|
Hi Does anybody know about a electronic or robotic store at L.A. (Los Angeles).? And the Address. Please Thanks Daniel ---...--- " `BETTER´ IS THE ENEMY OF `GOOD ENOUGH´" ---...--- (25 years ago, 22-May-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Handyboard/Miniboard Replacement
|
|
Why would you get flamed? it's just a conformal coating. they do it a lot in the military. It *IS* possible to fix a circuit board that's been protected in this way; when I was in the Navy one of the schools I went to was in microminiature (...) (25 years ago, 21-May-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Handyboard/Miniboard Replacement
|
|
(...) I'll get flamed for this, but I once dipped a board for an underwater robot in that liquid plastic stuff. It's at hardware stores, used for dipping wrench handles and stuff to make them more comfortable and electrically insulated. I held the (...) (25 years ago, 21-May-99, to lugnet.robotics.handyboard)
|
| |
| | Re: L.A. Store
|
|
Nope, That's in Norther California... Just a quick 6 hour drive though :-) --Mike (...) (25 years ago, 21-May-99, to lugnet.robotics.handyboard)
|
| |
| | Re: L.A. Store
|
|
(...) The Mondotronics Robot Store (www.robotstore.com) is located in San Rafael. Is that near LA? -- Will "been to California once" Bain (25 years ago, 21-May-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Can't get MiniBoard to Download??
|
|
Hello, I have not done anything with my Miniboard for quite some time but I believe what you are seeing is just the basic lighting due to the fact that there is nothing programmed. You need to put it in bootstrap mode and download the proper files (...) (25 years ago, 21-May-99, to lugnet.robotics.handyboard)
|
| |
| | Can't get MiniBoard to Download??
|
|
I am not sure if it is bad form to ask questions about the MiniBoard here on the HandyBoard list so I'll try keep it short. I am building my first MB, have completed assembly, visually scanned for any shorts, applied power (9V battery) and got the (...) (25 years ago, 21-May-99, to lugnet.robotics.handyboard)
|
| |
| | Handyboard/Miniboard Replacement
|
|
I have encountered of all things a gas grill which is controlled by a microcontroller of unknown origins. This contoller has bit the bullet and the grill vendor no longer supports it b/c they are out of business. The controller has 7 digital user (...) (25 years ago, 21-May-99, to lugnet.robotics.handyboard)
|
| |
| | IC and Pcode w/other boards?
|
|
Hello (Bonjour en anglais) I'm looking to use the freeware version on ic on a linux box with an F1 board. I've got the source for Pcode-2.81, IC-Unix, and as11. I have three questions that just *may* be answerable here (it's worth a shot). My first (...) (25 years ago, 20-May-99, to lugnet.robotics.handyboard)
|
