 | | Power Expansion Header On Handy
|
|
hi, I came to know that the power expansion can be used on J13 ( 1x4 pin jack). However, why there is a 2 positive holes and 2 negatives on this header? If i'm using a pair of DC motor 12V each, and i supply a 12v alkaline or NIMH rechargable (...) (26 years ago, 19-Nov-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Other batteries... -Reply
|
|
I guess what I'm wondering if the recharge circuit on the Handyboard Serial/charger board will work well with a sealed lead-acid/gel-cell. r than the pleasure of smelling boiling H2SO4 what could happen?? ould be convienent to just use the HB (...) (26 years ago, 19-Nov-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Other batteries...
|
|
Just a quick anecdote about Gel-Cells. I have a small and useless robot that simply rolls around on the floor and bumps off things. The motors are powered by a small Gel-Cell. I had run it that day and run the motor batteries flat, so I rigged a (...) (26 years ago, 19-Nov-98, to lugnet.robotics.handyboard)
|
| |
| | RE: PE4
|
|
Rajbala, PE4 is the 3rd pin on the 68HC11. Just by looking at the schematics in the HB manual I would think that it probably does connect to analog input 4. Joe Martin (...) (26 years ago, 19-Nov-98, to lugnet.robotics.handyboard)
|
| |
| | Help Y0-Y5
|
|
Sorry for my bad english ! i want to write - i have a big problem, i want to use the ports Y0-Y5 but i don´t know how i use them. Bernd Klein (26 years ago, 19-Nov-98, to lugnet.robotics.handyboard)
|
| |
| | Help
|
|
Hallo All , i have a big problem, i want to use the ports Y0-Y5 but i don´t know why. I need a ports for write and read. On Saturday i have my first sumo-robot contest and i need this ports !!!! I´m want to use a Sharp GP2D02 Distance Sensor, for (...) (26 years ago, 19-Nov-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Other batteries...
|
|
A gell cell battery is charged via a maximum allowed charging voltage. If the charger doesn't limit the charging voltage to less than 14 volts it will shorten the life of a 12v gell cell considerably. A Ni-Cad uses a constant charging current, but (...) (26 years ago, 19-Nov-98, to lugnet.robotics.handyboard)
|
| |
| | Re: motor port problem .
|
|
hi , Attached from the previous mail, I have already solved the problem listed below. It is the 7404 is damaged .What causes it? Any ideas? RIght now this problem that melted my socket on the L293, the supply I used is 12V supply to my 2 DC motors. (...) (26 years ago, 19-Nov-98, to lugnet.robotics.handyboard)
|
| |
| | Re: motor port problem .
|
|
hi, I have a big problem. I followed the method of yours that just lift up pin 8 of one L293 and wirewrapped it. The positive supply is wirewrapped to pin 8 . How about the negative supply of the batteries should insert or wirewrapped? I inserted (...) (26 years ago, 19-Nov-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Miniboard/download mode
|
|
(...) Check the voltage at the MOBD pin on the chip (not the socket, not the bottom of the board). If it is 5V with the switch in the one position, and ground (0V) in the other position, you may have a defective chip. Otherwise I'd guess open (...) (26 years ago, 18-Nov-98, to lugnet.robotics.handyboard)
|
