|
|
 | | Re: Gear Motors
|
| (...) Check out Herbach and Rademan at www.herbach.com for surplus DC gearhead motors. They often have 6-24 volt, optically encoded motors for $20-$25 each. J.V. -- ***...*** * John Vaughn Phone: 315-781-3906 * * Dept. of Math & Computer Science (...) (27 years ago, 16-Mar-98, to lugnet.robotics.handyboard)
| | | | | Re: pneumatics
|
| (...) The components you're looking for sound exactly like ones that came with my Lego Technic kit. The actuator cylinders come in two sizes (the big one's about the size you're looking for), and there's a compressor cylinder and pressure reservoir (...) (27 years ago, 16-Mar-98, to lugnet.robotics.handyboard)
| | | | | pneumatics
|
| does anyone know of a good sourec for pneumatics? Im especially interested in smaller pneumatics, like those about 1-2" long, with a stroke of 1-1.5" Thanks! phil (27 years ago, 16-Mar-98, to lugnet.robotics.handyboard)
| | | | | Nowbody can help me???
|
| I can't believe nowbody of the list users know how works the sound routines in the handyboard??? Please, if any have idea of how i can implement that on OTHER C COMPILER (don't interactive C), please anwser to my question. P.D,: Remember , the (...) (27 years ago, 16-Mar-98, to lugnet.robotics.handyboard)
| | | | | robots rising program
|
| Hi Guys, Get off the computer and tune to the discovery channel to catch this program comming on at 8:00 cst. I believe it is going to last one hour. Bye Terry P Gathright (27 years ago, 16-Mar-98, to lugnet.robotics.handyboard)
| | | | | ? Mabuchi RS280 motor
|
| Hello all, I've connected a mabuchi rs280 motor to the handyboard. When activated with the following command, "motor(0,12);" the motor speeds up and then stops, and the board also beeps. the ratings for the motor are as follows voltage range 6-9 (...) (27 years ago, 16-Mar-98, to lugnet.robotics.handyboard)
| | | | | RE: IC Pointer Questions
|
| Hi, thanks for your reply ... Why don't I use the encoder0_counts variable ? I want to create a multi-tasked environment with seperate processes for each wheel to calculate wheel speeds. The same code will be used to calculate speed for 4 wheels. (...) (27 years ago, 15-Mar-98, to lugnet.robotics.handyboard)
| | | | | Re: IC Pointer Questions
|
| (...) If I am understanding you right... I haven't looked at the encoder routines yet, but I am assuming encoder0_counts is global. Why not, just omit the pointer count from the _encoder struct and just use the global, since you already have it? (...) (27 years ago, 15-Mar-98, to lugnet.robotics.handyboard)
| | | | | Gear Motors
|
| I was wondering if anyone has a good source for fairly high quality, low cost gear motors that inteface well with the handy board. Right now i am using a cheap little, current hungry 3v toy bulldozer as a platform. I would love to find some nice (...) (27 years ago, 15-Mar-98, to lugnet.robotics.handyboard)
| | | | | IC Pointer Questions
|
| Howdy all, I finally attached an infrared reflectance sensor to my handyboard and it works! With my non-existent electronic experiences I managed to solder a resistance (330 ohms) to a three-legged sensor similar to the four-legged variant mentioned (...) (27 years ago, 15-Mar-98, to lugnet.robotics.handyboard)
|
|
