 | | Re: downloading
|
|
(...) Did you run the strip_cr utility on the .S19 file to make the file's lines end correctly? * Michael L. Ross/C33 | Lockheed Martin Eng & Sci Svcs Co. **** * Robotics Department | 2400 Nasa Rd. 1, Houston, TX 77058***** * (281)333-7094; (...) (28 years ago, 17-Feb-97, to lugnet.robotics.handyboard)
|
| |
| | HELP!
|
|
I hope that someone reading this can please help me with a problem that I am finding difficult to solve. I have completed section 4.3 "Micropro and Oscilaator cct" and confirmed that the oscillator is running. However after section 4.4 "Serial line (...) (28 years ago, 17-Feb-97, to lugnet.robotics.handyboard)
|
| |
| | problems downloading own .asm
|
|
Look at the .s19 file, and see if it's downloading anything between 0 and FF. (You should be able to stare at your .s19 file and the pcode for a while and figure out the 4 hex bytes which contain the address for a line). Downloading something to the (...) (28 years ago, 17-Feb-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Motors & handyboard
|
|
(...) What is 20? (...) Current meters have an internal resistance. The lower the current range the larger the resistance --- even with digital current meters. Some typical values For example: Digital Analogue Current Range R_meter R_meter 200 uA (...) (28 years ago, 17-Feb-97, to lugnet.robotics.handyboard)
|
| |
| | downloading
|
|
HI, I cannot get any .s19 file except for pcode_hb.s19 to download to the handy-board. This downloads and when I run IC it all works fine. The .s19 file I would like to download is just a normal .asm file assembled with as11.exe. I am just putting (...) (28 years ago, 17-Feb-97, to lugnet.robotics.handyboard)
|
| |
| | Compiling (interactive) C programs
|
|
Hi all, Some time ago I found a link somewhere on the handyboard page. This link referred to to someone who made a interactive C compiler for Unix environment. I would really like a compiler for the handyboard instead of the the C interpreter.(for (...) (28 years ago, 17-Feb-97, to lugnet.robotics.handyboard)
|
| |
| | DC Motors....
|
|
Does anybody know where I might get replacement motors, more suitable to the B, for the Tamiya Bulldozer Kit??? HELP!! These motors are not suitable, but the tank unit is nice. The motors are stable, but draw to much current. Also, the speed of the (...) (28 years ago, 16-Feb-97, to lugnet.robotics.handyboard)
|
| |
| | downloading
|
|
HI, I cannot get any .s19 file except for pcode_hb.s19 to download to the handy-board. This downloads and when I run IC it all works fine. The .s19 file I would like to download is just a normal .asm file assembled with as11.exe. I am just putting (...) (28 years ago, 16-Feb-97, to lugnet.robotics.handyboard)
|
| |
| | Re: MEMORY FAULT
|
|
This problem is answered in the Handy Board FAQ. You are loading the wrong s19 file. -Fred -- This message was composed using Articulate Systems' PowerSecretary, a Macintosh-based speech-to-text dictation system. Please forgive any sloppiness in the (...) (28 years ago, 16-Feb-97, to lugnet.robotics.handyboard)
|
| |
| | program for handyboard
|
|
I have started to assemble a handyboard and was wondering if there is a program that will allow the handyboard to simulate a walk through of a maze on my monitor or somthing similar of this type????? (28 years ago, 16-Feb-97, to lugnet.robotics.handyboard)
|
