 | | Re: A LEGO double-throw switch?
|
|
(...) Since turning the 9V wire connectors 90 degrees reverse the polarity, can't you play with how the wires are connected to the switches to re-reverse the polarity on one wire? (...) -Kyle (21 years ago, 22-Aug-05, to lugnet.robotics)
|
| |
 | | Re: Tripping a relay.
|
|
If you hit a 5v latching relay with 9v, will it damage it? (21 years ago, 22-Aug-05, to lugnet.robotics)
|
| |
 | | Re: A LEGO double-throw switch?
|
|
(...) Ok, Here's a partial solution (assuming you don't want to mechanically link the ends together). Given: Polarity Switch 1 - rotated forward by Forklift Polarity Switch 2 - rotated forward by crate when it arrives at the end Motor - located by (...) (21 years ago, 22-Aug-05, to lugnet.robotics)
|
| |
 | | Re: A LEGO double-throw switch?
|
|
(...) No, I think you should use one polarity switch, without handle to greatly reduce the friction needed to throw it. Putting the crate on the conveyor throws the switch, and when the crate gets to the other end it could push a lever, or better (...) (21 years ago, 22-Aug-05, to lugnet.robotics)
|
| |
 | | Re: A LEGO double-throw switch?
|
|
(...) Hi Brian, How will the package arriving at the other end "throw a switch?". Is there enough friction between the package and the belt? Will there be a mechanism in the belt itself to "go halfway and stop"? If you only used one polarity switch, (...) (21 years ago, 22-Aug-05, to lugnet.robotics)
|
| |
 | | Re: Tripping a relay.
|
|
Any body know of a typical consumer device that I could hack apart to find 6 to 9V "latching relay" from? (21 years ago, 22-Aug-05, to lugnet.robotics)
|
| |
 | | Re: A LEGO double-throw switch?
|
|
(...) hmm. At first, I would say "No". When you flip your switches at home, the switches could be in either of two states when the lights are "on". (one up, other down OR one down, other up) However, the LEGO polarity switches don't have to act like (...) (21 years ago, 22-Aug-05, to lugnet.robotics)
|
| |
 | | Re: A LEGO double-throw switch?
|
|
(...) Yes I'm sorry for not drawing it.. but here goes Imagine you have a cable with ground and a cable with 9V You need two single pole, double throw switches (I don't know what kind lego switches are) For both switches, connect one throw to 9V and (...) (21 years ago, 22-Aug-05, to lugnet.robotics)
|
| |
 | | A LEGO double-throw switch?
|
|
So I've got an application where a forklift loads a crate onto a conveyor belt. I could then start the conveyor belt up by having the forklift throw a polarity switch. What I would *like* is that when the crate gets to the other end, it somehow (...) (21 years ago, 22-Aug-05, to lugnet.robotics)
|
| |
 | | Re: Dual Hex small piston compressor (repost)
|
|
(...) Hi Kevin, Thanks. I am sorry for the slow feed back. I normally can only check in every week or two as I have no internet at home. Currently, we are on vacation in Lacaster, PA on our way to Ocean City, MD. :) (...) It is my understanding that (...) (21 years ago, 22-Aug-05, to lugnet.technic, lugnet.robotics)
|