 | | Re: The Great Ball Contraption
|
|
"David Koudys" <dkoudys@redeemer.on.ca> wrote in message news:IA3zL9.xKJ@lugnet.com... (...) What's the big deal? Either you can make a module to comply with simple specs, or you can't. If you need more space and can't fit everything inside 1 - (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) <snip> (...) I love standards, but I also like the 'variedness' of the GBC modules--trying to get somethign specific hammered down, like 'only 32x32 baseplates with the bin in the bottom left corner' might be a little difficult. As it is, (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | RE: The Great Ball Contraption
|
|
<SNIP> (...) Personally, I think something similar to the moonbase concept should be applied--an input bin with opening or edge at a given heighth and width and placed in a specifica location on a standard footprint size, or perhaps by allowing (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) I completely agree with that assessment. However, the premise is that I'm using a 32x32 baseplate with the hopper in the bottom left hand corner--using that premise, the module can be used either in-line, or 90 degrees. If one does not use the (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
news-gateway@lugnet.com wrote on 01/10/2005 10:01:48 AM: (...) thus the (...) module, (...) or 90 (...) That assumes that there is nothing in front of the hopper. There is nothing to say that you are limited to a module 32 studs deep. If you choose (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | RE: TGBC - The Weakest Link?
|
|
<SNIP> (...) Like a train layout, how about routing/switching module to create multiple ball routes? This way, if any one module acts up, only modules affected in that path need to be dealt with. Given the standards (regarding input/output bin (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) Not to oversimplify, but I mean if the 'standard' for the ball contraption is 32 studs from the front of the hopper to the back edge of the baseplate, and thus I personally would probably grab a 32 x 32 stud baseplate to build on, thus the (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) Is there something that a module builder can not do because the standard is too simple? Steve (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
Steve Baker writes: > So simply write into the rules that everyone who submits a left hand > turn has to submit a corresponding right hand turn or they won't > be accepted. Excellent idea! But it's even easier than that!! Do NOT change the (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
tmassey@obscorp.com writes: > Or not: leave the standard as it is (except for specifying that the space > above the input belongs to the previous module), and have the organizers > build (or specificially request) out-of-spec modules to accomplish (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|