To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 23264 (-10)
  Re: The Great Ball Contraption
 
(...) In addition, there's an actual *reason* why that is set up that way. Can you picture trying to set up a large scale GBC if we need a certain number of "turns" and "straights"? There could also be interference issues if the rear of the GBC line (...) (22 years ago, 7-Jan-05, to lugnet.robotics)
 
  Re: The Great Ball Contraption
 
(...) Man, this project is so cool!!!!!!! (...) I am so looking forward to it. (...) No questions...... but one comment..... Chris may be King of rtl, and Dave is King of the Sheets! Move over guys, because Steve has got balls, and that makes him (...) (22 years ago, 7-Jan-05, to lugnet.robotics)
 
  Re: The Great Ball Contraption
 
"Brass Tilde" <brasstilde@insightbb.com> wrote on 01/07/2005 01:52:19 PM: (...) edge, (...) participate. (...) a (...) correct (...) and (...) While what you're saying will work fine, the standard does say: Each module should have an "in" basket, (...) (22 years ago, 7-Jan-05, to lugnet.robotics)
 
  RE: The Great Ball Contraption
 
(...) Soccer balls, like Ruffles, have ridges... (22 years ago, 7-Jan-05, to lugnet.robotics)
 
  Re: The Great Ball Contraption
 
(...) The standard doesn't explain this very well, because I'm really not sure how to write it. A module can be any size, but the input and output should be on opposite sides, with the front of the input being no more than 32 studs from the back of (...) (22 years ago, 7-Jan-05, to lugnet.robotics)
 
  RE: The Great Ball Contraption
 
(...) I happen to have a LEGO basketball set on my desk... Eyeing it up against a ruler, it is 14mm in diameter. Depending on design choice, one might consider using only LEGO basketballs or soccer balls because other materials would have different (...) (22 years ago, 7-Jan-05, to lugnet.robotics)
 
  Re: The Great Ball Contraption
 
(...) This post will be overkill I am sure but this Bricklink store sells has 42 soccer balls $.10 US a piece (URL) (22 years ago, 7-Jan-05, to lugnet.robotics)
 
  Re: The Great Ball Contraption
 
(...) I'll point out that the standard as it's defined pictorially allows for a non-linear layout just as it stands. As long as the input in in the correct place relative to the previous block's output, and the output is placed correctly relative to (...) (22 years ago, 7-Jan-05, to lugnet.robotics)
 
  Re: The Great Ball Contraption
 
(...) I'd really recommend against using anything but LEGO balls. If you just want to play around and test, one good place to get a couple balls are the LEGO NBA sets. I've seen them on sale all over. Using any other type of balls will not give you (...) (22 years ago, 7-Jan-05, to lugnet.robotics)
 
  Re: The Great Ball Contraption
 
(...) Well, it's LEGO - it's just a tad smaller than 2 studs in diameter. If you've got a marble or wooden ball that will roll between two walls two studs apart (clearance about 1.5 mm on each side) you've got the size. The only real problem is (...) (22 years ago, 7-Jan-05, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR