To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 23259 (-10)
  RE: The Great Ball Contraption
 
(...) I happen to have a LEGO basketball set on my desk... Eyeing it up against a ruler, it is 14mm in diameter. Depending on design choice, one might consider using only LEGO basketballs or soccer balls because other materials would have different (...) (22 years ago, 7-Jan-05, to lugnet.robotics)
 
  Re: The Great Ball Contraption
 
(...) This post will be overkill I am sure but this Bricklink store sells has 42 soccer balls $.10 US a piece (URL) (22 years ago, 7-Jan-05, to lugnet.robotics)
 
  Re: The Great Ball Contraption
 
(...) I'll point out that the standard as it's defined pictorially allows for a non-linear layout just as it stands. As long as the input in in the correct place relative to the previous block's output, and the output is placed correctly relative to (...) (22 years ago, 7-Jan-05, to lugnet.robotics)
 
  Re: The Great Ball Contraption
 
(...) I'd really recommend against using anything but LEGO balls. If you just want to play around and test, one good place to get a couple balls are the LEGO NBA sets. I've seen them on sale all over. Using any other type of balls will not give you (...) (22 years ago, 7-Jan-05, to lugnet.robotics)
 
  Re: The Great Ball Contraption
 
(...) Well, it's LEGO - it's just a tad smaller than 2 studs in diameter. If you've got a marble or wooden ball that will roll between two walls two studs apart (clearance about 1.5 mm on each side) you've got the size. The only real problem is (...) (22 years ago, 7-Jan-05, to lugnet.robotics)
 
  Re: The Great Ball Contraption
 
(...) Yep. The IN basket is really more of a "target zone" - the upstream module should drop the balls into your IN basket zone (really, the 8x8 center section) from a height of at least 10 bricks (no specified upper limit, so when building your (...) (22 years ago, 7-Jan-05, to lugnet.robotics)
 
  Re: The Great Ball Contraption
 
(...) Really, the only thing defining a "module space" is a flat L & R edge, and no part of the module extending more than 32 studs from the front edge of the input bin "zone" - the footprint need not be remotely rectangular, nor is there a set (...) (22 years ago, 7-Jan-05, to lugnet.robotics)
 
  Re: The Great Ball Contraption
 
(...) Sure enough, that'll happen. What about the sawdust envy that LEGO soccer balls will inevitably suffer from? Ed (22 years ago, 7-Jan-05, to lugnet.robotics)
 
  Re: The Great Ball Contraption
 
(...) Or someone who owns a soccer ball could measure it and publish the size. Most craft stores sell a selection of little wooden balls. It might be cheaper to buy a few about the right size rather than paying to mail genuine Lego ones? Of course, (...) (22 years ago, 7-Jan-05, to lugnet.robotics)
 
  Re: The Great Ball Contraption
 
(...) Cool - That works for me :) Steve - on the page it says "The IN basket should be 10 studs by 10 studs (outside dimension) with an 8x8 opening, and should be 10 bricks (beams) tall." and "Each module should be able to accept balls at an average (...) (22 years ago, 7-Jan-05, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR