 | | Re: Why NQC over Robolab?
|
|
(...) I suspected as much. (...) Well crud. Now I'm going to have to go out and get one of those things. (...) Suffice to say, Robolab does not currently support the Spybot. Sounds like an interesting project though.... Tom (22 years ago, 13-Dec-04, to lugnet.robotics)
|
| |
 | | Re: Replacement Firmware Released
|
|
(...) Congrats again on the significant 'smart stuff'! Your feedback on the sensor bugs did the fix at the right time too. This firmware obsoletes a lot of Robolab and other RCX approaches, and analog interfacing ... What am I talking about? Motors (...) (22 years ago, 12-Dec-04, to lugnet.robotics)
|
| |
 | | Re: Ultimate ROBOLAB
|
|
(...) Yes and no! In fact, the name Ultimate ROBOLAB was chosen together with the father of ROBOLAB Prof Chris Rogers. This might be a bit confusing as to compatibility. But compatibility there is: 1. Most of the "modifiers" like "Red (...) (22 years ago, 12-Dec-04, to lugnet.robotics)
|
| |
 | | Re: Ultimate ROBOLAB
|
|
(...) I think Ultimate Robolab sounds very cool. Unfortunately, I think some Robolab users may be confused by the name and think that their Robolab programs will be completely reuseable in Ultimate Robolab. As far as I can figure this is simply not (...) (22 years ago, 12-Dec-04, to lugnet.robotics)
|
| |
 | | Re: Why NQC over Robolab?
|
|
(...) Then I would like to announce that NQC supports the MicroScout and CodePilot bricks. It has had this support for several years. (...) The Spybot is a fully programmable lego brick like the RCX and Scout. Like the Scout its firmware is in ROM. (...) (22 years ago, 12-Dec-04, to lugnet.robotics)
|
| |
 | | Re: Ultimate ROBOLAB
|
|
Thanks, Claude, for the detailed response and thank you, Larry Whitman, for the following link: (URL) ...and the 303 page Robolab Manual. Jerry (22 years ago, 12-Dec-04, to lugnet.robotics)
|
| |
 | | Glue to use with lego pieces
|
|
Hi, what is the best kind of glue to use with lego pieces, when building homebrew devices? I usually work with "super bonder" but it is kind of messy... Just know i am triyng to glue a Led onto a 2x2 lego brick, without any success... Patrick (22 years ago, 12-Dec-04, to lugnet.robotics)
|
| |
 | | Re: Replacement Firmware Released
|
|
(...) hello Dick, it really looks great. What I was wondering, what do you've in mind for licensing ? Is it freeware, or is it only freeware during beta-test ? thanks Stef Mientki (22 years ago, 12-Dec-04, to lugnet.robotics)
|
| |
 | | Re: Ultimate ROBOLAB
|
|
(...) Ultimate is close enough to standard ROBOLAB to allow easy programming too. Ultimate certainly is not reseved for high specialists. (...) Right. The gain is : memory, speed and control; the loss is : longer download speed. (...) So did I. But (...) (22 years ago, 12-Dec-04, to lugnet.robotics)
|
| |
 | | Re: Ultimate ROBOLAB
|
|
(...) Claude, what you have done is very exciting. While I program all my projects using Robolab, I suspect that 'Ultimate Robolab' is so far above my capabilities that I should not attempt to use it. Here's what I understand: Ultimate Robolab is a (...) (22 years ago, 11-Dec-04, to lugnet.robotics)
|
| |
 | | binaural sensor
|
|
also look at this (URL) could be the base for a robot that is listening to "His master's voice" :) (22 years ago, 11-Dec-04, to lugnet.robotics)
|
| |
 | | Tower of Hanoi
|
|
Have a look at (URL) is a recursive solution of the puzzle based on Ultimate ROBOLAB. (22 years ago, 11-Dec-04, to lugnet.robotics)
|
| |
 | | Re: Why NQC over Robolab?
|
|
(...) It is the latter. (...) I've never messed w/a spybot so I can't give a definitive answer but if the spybot is controlled via VLL, then it should be supported. Tom (22 years ago, 11-Dec-04, to lugnet.robotics)
|
| |
 | | Re: Replacement Firmware Released
|
|
(...) I am a Robolab user. I followed instructions replacing firmware.txt with the replacement file as instructed. The download went smoothly,immediately upon finishing (two beeps) the LCD screen started counting in M.SS.S. format indicating a (...) (22 years ago, 11-Dec-04, to lugnet.robotics)
|
| |
 | | Re: Replacement Firmware Released
|
|
(...) The free version of Dick Swan's firmware does not include support for 32-bit float variables or long integers. From the Quick Start Guide: "The firmware distributed is the 10 times faster version. It does not include support for floats and (...) (22 years ago, 10-Dec-04, to lugnet.robotics)
|
| |
 | | Re: Replacement Firmware Released
|
|
"Philippe Hurbain" <philohome@free.fr> wrote in message news:I8II4B.13Io@lugnet.com... (...) (optional) (...) hi philo i found this sentence "Floating point variables New opcodes and intrinsic variables have been added to firmware to support 32-bit (...) (22 years ago, 10-Dec-04, to lugnet.robotics)
|
| |
 | | Re: Why NQC over Robolab?
|
|
(...) I'm having a hard time grasping the concept for some reason. In Robolab do you say "I want to write a program for the MicroScout" or do you simply have a component that can be placed into a script written for the Scout which says "send a VLL (...) (22 years ago, 10-Dec-04, to lugnet.robotics)
|
| |
 | | Re: Why NQC over Robolab?
|
|
(...) Robolab uses the Scout as an intermediary. Essentially, you program the Scout to program the microScout. Using the Scout, scripts or direct commands are sent to the MicroScout. Robolab supports the Code Pilot in the same fashion. Although this (...) (22 years ago, 10-Dec-04, to lugnet.robotics)
|
| |
 | | Re: Why NQC over Robolab?
|
|
(...) Can you explain exactly how RoboLab support the MicroScout? I'm guessing you can write simple scripts that can be downloaded using the USB tower's VLL support. Is that right? John Hansen (22 years ago, 10-Dec-04, to lugnet.robotics)
|
| |
 | | Re: Replacement Firmware Released
|
|
(...) Hello Dick, Congratulation for this new release! Just to make things clear: it seems that this version doesn't include (optional) 32 bits/floating poins support? Philo (22 years ago, 10-Dec-04, to lugnet.robotics)
|