 | | Lego® Technic Motor (43362) internals —Philippe Hurbain
|
| | | I received two new 9V mini-motors from S@H, that was of the new variety described by Mark Riley ((URL) lead me to remove back cover, but it was wired to the rest of the motor. So I put it back in place... no luck, the motor didn't turn any more :c( (...) (22 years ago, 11-Dec-02, to lugnet.robotics, lugnet.technic)
|
| | | |
| | | | | Re: Lego® Technic Motor (43362) internals —Brian B. Alano
|
| | | | | Thanks for the sacrifice! From what I can see, it looks like there's room in this motor for an axle *hole* rather than an axle shaft. What a shame... (...) (22 years ago, 11-Dec-02, to lugnet.technic)
|
| | | | | |
| | | | | | | Re: Lego® Technic Motor (43362) internals —Philippe Hurbain
|
| | | | | | | Indeed, I see no technical or dimensions problems that would prevent using a hole. But perhaps that was not possible in 71427 - and compatibility rules !!! Philo (...) A small one, it works fine now! (...) (22 years ago, 11-Dec-02, to lugnet.technic)
|
| | | | | | | |
| | | | | | | | | Re: Lego® Technic Motor (43362) internals —Juergen Stuber
|
| | | | | | | | (...) I think it should have been possible there as well (I have a disassembled 71427 that was broken). As for compatibility, if you put an axle 2 into the hole it should be pretty much equivalent, maybe not as strong mechanically. Another question (...) (22 years ago, 12-Dec-02, to lugnet.technic)
|
| | | | | | | | |
| | | | | | | Re: Lego® Technic Motor (43362) internals —Tobbe Arnesson
|
| | | | | | (...) It should be fairly easy to saw off the axle and glue a bush to the shortened axle, thus getting an axlehole instead of the protruding pin. The mainproblems would be to - Get the bound strong - Get the bush centered on the axle Perhpas some (...) (22 years ago, 12-Dec-02, to lugnet.technic)
|
| | | | | | |
| | | | | | | | Re: Lego® Technic Motor (43362) int ernals —Juergen Stuber
|
| | | | | | (...) Notoriously difficult (...) I'd rather use a hacksaw on a technic angle or axle connector. (...) Probably not so easily. (...) I'd rather propose the following operation (totally theoretic, use at your own risk): Saw of the protruding axle and (...) (22 years ago, 12-Dec-02, to lugnet.technic)
|
| | | | | | |
| | | | | Re: Lego® Technic Motor (43362) internals —Eric Sophie
|
| | | | | Nice page, I enjoyed your site too. e www.mylegomaster.com (22 years ago, 12-Dec-02, to lugnet.robotics, lugnet.technic)
|
| | | | | |
| | | | | Re: Lego® Technic Motor (43362) internals —Tobbe Arnesson
|
| | | | (...) and it contains two 43362 motors. These are not the same: (URL) one without the "backholes" spins like the older geared motor, for aprox six seconds given a twist on the shaft, the other one for but one second... The mystery deepens... (...) (22 years ago, 14-Dec-02, to lugnet.robotics, lugnet.technic)
|
| | | | |
| | | | | | Re: Lego® Technic Motor (43362) internals —Philippe Hurbain
|
| | | | Hi Tobbe, My guess is that your friend actually got one 43362 and one 71427, the latter beeing enclosed in a 43362 case. If you look at 43362 enclosure photo ((URL) you see that there are 4 plastic pins in corners that are used to secure 71427 core (...) (22 years ago, 15-Dec-02, to lugnet.robotics, lugnet.technic)
|
| | | | |
| | | | | | Re: Lego® Technic Motor (43362) internals —Tobbe Arnesson
|
| | | | (...) Ah! (...) My friend wont bother much since the boxes are for education at hiw workplace. I conducted a quick test with one 71427-002 and one 43362 (with new internals), put them back to back with a 8462 wheel on each axel and a 9V small (...) (22 years ago, 15-Dec-02, to lugnet.robotics, lugnet.technic)
|
| | | | |
| | | | | | Re: LegoX Technic Motor (43362) internals —Steve Baker
|
| | | | (...) It's 6.11125 meters. (...) Yes - it's hard to tell because the difference in speeds will depend on the load on the motors - loading them either more or less would alter their characteristics relative to each other. (...) Yes - I think so. (...) (22 years ago, 15-Dec-02, to lugnet.robotics)
|
| | | | |
