 | | Re: Lubricating technic turntables
|
|
<snip> from using different types of yoyos and other things i have found that the best for inert lubricating is silicon lubricant, there are also some other lubes for nylon that i can't think of but i do know that they are out there. some vcr repair (...) (24 years ago, 4-Apr-01, to lugnet.robotics)
|
| |
| | Re: NQC for Palm
|
|
<snip> it's too bad that all of you just HAVE to use a palm OS device. someone a long time ago ported nqc to windowsce and it works fine, i'm able to do on the fly programming and uploading with a first generation device, which i'm actually unhappy (...) (24 years ago, 4-Apr-01, to lugnet.robotics)
|
| |
| | Question about the UBS
|
|
Is there is any information on what will be contained in the 'Ultimate Builder's Set'? (24 years ago, 4-Apr-01, to lugnet.robotics)
|
| |
| | Re: I wish Lego made an "Anti-Backlash Gear"
|
|
(...) I know of 1 type of zero-lash/anti backlash geartrain. It's hard to put it in words but I'll try. My example assumes there are only 2 shafts but it can be applied to as many shafts as you need. In my example S1 represents our first shaft. (...) (24 years ago, 5-Apr-01, to lugnet.robotics, lugnet.technic)
|
| |
| | Re: Lubricating technic turntables
|
|
(...) Before someone ruins their pneumatics..... Brake Fluid will ruin many plastics, will remove paint, and can even damage certain types of rubber seals. The rubber parts in an automotive brake system are made from special rubber that is made to (...) (24 years ago, 5-Apr-01, to lugnet.robotics)
|
| |
| | Re: NQC for Palm
|
|
(...) Yes - NQC is developed on a Mac so PowerPC big-endian is actually where most of the testing is done, but I don't recall ever running into an endian problem. One of the builds (for Mac MPW) targets 68K, but with slightly difference options than (...) (24 years ago, 5-Apr-01, to lugnet.robotics)
|
| |
| | Re: I wish Lego made an "Anti-Backlash Gear"
|
|
Interesting , but we need one for Lego! I do see what you are saying, and It is an interesting solution,, although a little hard to visualize...Thanks! (...) (24 years ago, 5-Apr-01, to lugnet.robotics, lugnet.technic)
|
| |
| | Re: I wish Lego made an "Anti-Backlash Gear"
|
|
(...) I was going to say this solution is easy, but then I tried it. There are only two shaft's in this example. As lego don't make don't make a 'double width gear' You'd have to use four to make it in lego. All you'd need is three normal 16 tooth (...) (24 years ago, 5-Apr-01, to lugnet.robotics, lugnet.technic)
|
| |
| | Re: I wish Lego made an "Anti-Backlash Gear"
|
|
Hmmm... (...) (24 years ago, 5-Apr-01, to lugnet.robotics, lugnet.technic)
|
| |
| | Re: I wish Lego made an "Anti-Backlash Gear"
|
|
(...) Explain 'Hmmm...' :-) I of course omitted the fact that my solution as described produces no mechanical advantage just a shaft going in the opposite direction. Of course, you can always replace the pair of gears on the second shaft with a pair (...) (24 years ago, 5-Apr-01, to lugnet.robotics, lugnet.technic)
|
