Subject:
|
Re: Recipricating motion problems
|
Newsgroups:
|
lugnet.robotics
|
Date:
|
Thu, 30 Nov 2000 16:38:50 GMT
|
Viewed:
|
1995 times
|
| |
|
|
You need gears or a cam that allows an adjustment in the distance from the
centerline of the shaft. A 24 tooth gear and a 40 tooth gear would allow you
to accomplish such action. I find the cam is very useful as the driven
element. You can always place a cam on the shaft with the reciprocating
gear to allow some further adjustment.
--
Bob Fay
rfay@we.mediaone.net
The Shop
http://www.geocities.com/Heartland/Bluffs/7900/
http://users5.50megs.com/bobfay
California
USA
"Jason Stern" <2busytobe@home.com> wrote in message
news:3A265EF8.A88E7AE0@home.com...
> I have two 24 tooth gears. The lower gear is one hole down, six holes
> over from the upper gear. Like so (the @ are where the center of the
> gears are):
>
> @
> @*****
> ^1 2^
> I need to make it so that by turning gear 1 continusaly, in only one
> direction, gear 2 turns a 1/4 turn, and the goes back to the starting
> position (ie gear 2 turns 90 degrees clockwise, then turns 90 degrees
> counterclockwise. it can not turn back through use of a rubber band, the
> rotating must come soley from gear 1, which is turning in only one
> direction) How could I go about doing this? What I have been trying so
> far is to use an axle like those on a train, with one end of the axle
> attach to one of the holes in gear 1 and the other end attached to one
> of the holes in gear 2. So far i have gotten gear 2 to rotate 45 and
> back and i have gotten it to rotate more than 90, but not back (not sure
> by how much it over rotated, after 90, the gear hits stuff and can't
> rotate anymore, so it stops moving, and stops gear 1 from moving,
> grinding everything to a halt) I have only tried a few combinations of
> axles and connectors with the gears, but rather than go through all of
> them (there must be at least a hundred!), has anyone done this before
> and gotten it to work? Does anyone have any other suggestions how i
> could do this?
>
> Jason
>
> P.S. If this confuses you, I have an mlcad that shows how it is supposed
> to work. Drop me a line and I'll send it to you.
>
|
|
Message has 1 Reply:
 | | Re: Recipricating motion problems
|
| sorry but you lost me, whats a cam? If you mean an off center 40 tooth gear, i already tried that but it didn't work. i could get it to turn th other , but i could get it to turn it back again Jason (...) (26 years ago, 30-Nov-00, to lugnet.robotics)
|
Message is in Reply To:
| | Recipricating motion problems
|
| I have two 24 tooth gears. The lower gear is one hole down, six holes over from the upper gear. Like so (the @ are where the center of the gears are): @ @***** ^1 2^ I need to make it so that by turning gear 1 continusaly, in only one direction, (...) (26 years ago, 30-Nov-00, to lugnet.robotics)
|
4 Messages in This Thread:
 
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
This Message and its Replies on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|
