To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *8326 (+10)
  Re: homebrew Temp sensor
 
(...) I damn well know what an elco is, thank you, and, I've never seen one blow up from <12V.. they can get a bit hot, and make a little plop, but I've personally never seen them shower the room with shrapnel. Which of course, is not saying that (...) (28 years ago, 23-Jan-99, to lugnet.robotics)
 
  Re: Pneumatic Tanks
 
(...) The heroine dealer on the corner? Jasper (28 years ago, 23-Jan-99, to lugnet.robotics)
 
  Re: Toy motors
 
right, this is a good answer. you buy a device called an "electronic speed controller". this connects like a servo to the HB (3 wire connection) and has outputs to drive high current DC motors. you also connect a separate power supply to the device. (...) (28 years ago, 23-Jan-99, to lugnet.robotics.handyboard)
 
  Re: Working around the 3 output limitation
 
(...) The one with two studs in the middle, and two holes at the ends? and you then have one of the half-bushings with teething (1) thaty it rests on? I would say that those teehings are too deep too slip comfortably, but I haven't tried it out. (1) (...) (28 years ago, 23-Jan-99, to lugnet.robotics)
 
  Re: Toy motors
 
sorry, send my msg before it was done. right, this is a good answer. you buy a device called an "electronic speed controller". this connects like a servo to the HB and has outputs to drive high current DC motors. you also connect a separate power (...) (28 years ago, 23-Jan-99, to lugnet.robotics.handyboard)
 
  Re: Sensor monitoring
 
(...) that (...) What about using homebrew light sensors made from CdS photoresistors? Seems like it would be possible to multiplex them since they don't require power. (28 years ago, 23-Jan-99, to lugnet.robotics)
 
  Re: RCX message's
 
Rudi Slomp skrev i meddelandet <36A92700.4A0B@iaehv.nl>... (...) I think these are Mindstorms specific - sending messages through the IR port. -- Anders Isaksson, Sweden BlockCAD: (2 URLs) (28 years ago, 23-Jan-99, to lugnet.robotics)
 
  Re: Ultrasonic sensor
 
(...) Firstly, it looks like the sensor board can be powered from the HB using the motor power header (J13). This is good, because the two should share a common ground. Based on the schematic and the web page description, it looks like this type of (...) (28 years ago, 23-Jan-99, to lugnet.robotics.handyboard)
 
  Re: senor signal line back to HD
 
(...) The sensor should be grounded to the HB. (...) Oh yes. Quite a few messages this past week suggest how to avoid frying your sensor ports with excessive voltage. -- Will , , __@_/ \_@__ |/ | /__, o @_/ )\ ) ( \ (\/\\, ~~~...~~~ ' ` ~~~...~~~ ` (...) (28 years ago, 23-Jan-99, to lugnet.robotics.handyboard)
 
  Stack Overflow
 
Hi everyone: I'm trying to download a rather large chunk of code to the HandyBoard, and I'm having a problem when I exceed a certain number of instructions in a procedure I'm running. When I try to download the code, I get the error "yacc stack (...) (28 years ago, 23-Jan-99, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR