To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *4331 (+10)
  Steppr motor pulse problem
 
Hi, I've encounter some problem on using the stepper motor with my self-built driver. I am not using the driver in the HB. I have to build out a driver. The driver chip I use is L298 and logic gate chip is L297 or 374( this chip also use in HB) . (...) (28 years ago, 26-Aug-98, to lugnet.robotics.handyboard)
 
  Re: HB's analog inputs
 
(...) Edmund, Typically the solution is to pass the 4-20 mA through a 250 ohm resistor and measure the voltage across that resistor. As long as your A/D input impedance is high, it can be ignored. A resistor is essentially a current to voltage (...) (28 years ago, 26-Aug-98, to lugnet.robotics.handyboard)
 
  problems with main()
 
I posted earlier in the week about having a problem with the SRAM. I have determined that there is not a problem with the SRAM on the handyboard. The problem is that "main()" is not executing on reset like it is supposed to. The program that I am (...) (28 years ago, 26-Aug-98, to lugnet.robotics.handyboard)
 
  HB's analog inputs
 
does anyone know if the handy board's analog inputs can accept analog current output(4-20mA) from a photo-electric distance sensor? (e.g. the sensor might return 4mA if the object is 1 ft away and 15mA if it's 3 ft away) or can it only accept (...) (28 years ago, 26-Aug-98, to lugnet.robotics.handyboard)
 
  Re: Analogue sonar design.
 
Jeroen van der Vegt, Let me suggest some articles. First "Sonars on the Cheap" by Keith Payea page 20 of the Fall 1995 issue of The Robotics Practitioner. This looks lie about a $30 design. Second "An Experimenter's Cheap Robotic Sonar System" by (...) (28 years ago, 26-Aug-98, to lugnet.robotics.handyboard)
 
  [Interactive C features]
 
Hello All, my name is Marcelo Manjon and i am 5th year graduate student of Mechatronics Engineering at Politechnic School of Sao Paulo University. Turns out that this year i'll be developing a Micromouse Robot using the MIT Handy Board. I have (...) (28 years ago, 26-Aug-98, to lugnet.robotics.handyboard)
 
  Re: [Interactive C features]
 
(...) You could use a one dimensional array of length width*height such that: cellMazeWhatever[x][y] is turned into cellMazeWhatever[(x-1)*width+y] (28 years ago, 26-Aug-98, to lugnet.robotics.handyboard)
 
  Re: [Interactive C features]
 
You can also upgrade to IC 3.1/3.2. Among the improvements include support for multidimensional arrays. -- Randy ---...--- (...) (28 years ago, 27-Aug-98, to lugnet.robotics.handyboard)
 
  Re: Steppr motor pulse problem
 
Hi Philip, are you shure, you have the right pins from the stepper to the outgoing pins from your chip. Have your stepper 4,5 or 6 cables? If you exchange the cables, your stepper motor only do some vibrations or doing nothing. The easiest way to (...) (28 years ago, 27-Aug-98, to lugnet.robotics.handyboard)
 
  Re: Steppr motor pulse problem
 
Phillip First step is to put a piece of tape on the shaft so that you can clearly see the shaft turn. Next determine what kind of motor you have (you have probably already done this). Get an ohm meter and determine which wires are connected to (...) (28 years ago, 27-Aug-98, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR