 | | Re: maze solving algorithm
|
|
(...) Can you post your source code please? Thanks, Jona <http:www.24tooth.com LEGO Robotics Group of Ann Arbor> (23 years ago, 16-Jun-03, to lugnet.robotics)
|
| |
 | | Re: EGAD! (pneumatics)
|
|
(...) Yes, the switches would need to remember their last set state. Ideally, this would be done through the use of electric pneumatic switches which, when not receiving any power, simply stay in the last position they were set in. If this isn't (...) (23 years ago, 16-Jun-03, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: EGAD! (pneumatics)
|
|
(...) IMHO, it would be much simpler and precise to measure directly pulse width instead of voltage, that could be done easily with a small microcontroller... Philo www.philohome.com (23 years ago, 16-Jun-03, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: MOC - Small Pneumatic Biped Walker
|
|
(...) Hi Paul, I use a electronic schematic style when drawing out my pneumatic circuit designs these days. The combination of a piston that is linke to a pneumatic switch is simply a box, with X and C on the left edge, representing the eXpand and (...) (23 years ago, 16-Jun-03, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: EGAD! (pneumatics)
|
|
(...) When using LEGO's firmware and NQC the maximum number of power levels you have is 8 (plus off?), so the most you can identiy is 9. This of course presumes that current draw by your compressor's motors doesn't mess with the voltage going into (...) (23 years ago, 16-Jun-03, to lugnet.technic, lugnet.robotics)
|
| |
 | | [rtlToronto] BrickFest Pipe Racers
|
|
Hi guys, I'd like to tentatively announce the rtlToronto Robotics Event at BrickFest 2003 in Washington DC: (URL) will be run by Jeff Van Winden and yours truly at everyone's favourite Lego enthusiast gathering this August and you're invited to be a (...) (23 years ago, 16-Jun-03, to lugnet.org.ca.rtltoronto, lugnet.events.brickfest, lugnet.robotics.events) !
|
| |
 | | Re: EGAD! (pneumatics)
|
|
(...) I was thinking that one could just use an ADC to directly convert the analog voltage level to a digital number of however many bits you could resolve it to and then taking that binary number to address a demux and have the demux's outputs (...) (23 years ago, 16-Jun-03, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: EGAD! (pneumatics)
|
|
(...) Wow, that'll be great! (...) Keep at it. (23 years ago, 16-Jun-03, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: MOC - Small Pneumatic Biped Walker
|
|
(...) Thanks Paul! You are always so kind. The pneumatic control circuit is similar to one found in a two double acting cylinder engine, except slightly different. It makes the walking pace more even from side to side. (...) Kevin (23 years ago, 16-Jun-03, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: MOC - Small Pneumatic Biped Walker
|
|
(...) What can I say? Yet another amazing creation. You have a pneumatic control circuit in there somewhere, I think. I know what you mean about the small pneumatic cylinders needing such high pressure to move a switch. The engine I built following (...) (23 years ago, 16-Jun-03, to lugnet.technic, lugnet.robotics)
|