 | | [rtlToronto] BrickFest Pipe Racers
|
|
Hi guys, I'd like to tentatively announce the rtlToronto Robotics Event at BrickFest 2003 in Washington DC: (URL) will be run by Jeff Van Winden and yours truly at everyone's favourite Lego enthusiast gathering this August and you're invited to be a (...) (23 years ago, 16-Jun-03, to lugnet.org.ca.rtltoronto, lugnet.events.brickfest, lugnet.robotics.events) !
|
| |
 | | Re: EGAD! (pneumatics)
|
|
(...) I was thinking that one could just use an ADC to directly convert the analog voltage level to a digital number of however many bits you could resolve it to and then taking that binary number to address a demux and have the demux's outputs (...) (23 years ago, 16-Jun-03, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: EGAD! (pneumatics)
|
|
(...) Wow, that'll be great! (...) Keep at it. (23 years ago, 16-Jun-03, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: MOC - Small Pneumatic Biped Walker
|
|
(...) Thanks Paul! You are always so kind. The pneumatic control circuit is similar to one found in a two double acting cylinder engine, except slightly different. It makes the walking pace more even from side to side. (...) Kevin (23 years ago, 16-Jun-03, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: MOC - Small Pneumatic Biped Walker
|
|
(...) What can I say? Yet another amazing creation. You have a pneumatic control circuit in there somewhere, I think. I know what you mean about the small pneumatic cylinders needing such high pressure to move a switch. The engine I built following (...) (23 years ago, 16-Jun-03, to lugnet.technic, lugnet.robotics)
|
| |
 | | MOC - Small Pneumatic Biped Walker
|
|
The other day I was given a challenge to make a small biped using small pneumatic pistons. Normally I don't use small pistons in combinations with switches, because the pressure must be increadibly high for a small piston to flip a pneumatic switch (...) (23 years ago, 15-Jun-03, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: maze solving algorithm
|
|
From: "Bluey" <Wolf_and_eagle@spam...yahoo.com> (...) maze (...) I forogt something. The robot was suppose to flood the maze starting in the finish square mapping how far each square is from the finish square. There is still some probelms with the (...) (23 years ago, 15-Jun-03, to lugnet.robotics)
|
| |
 | | Re: Varying the output voltage?
|
|
(...) The power motors that come with the RIS are very efficient, so the load is very light and speed changes very little. Then of course it depend on your robot, if you use caterpillar tracks you will generally have more load than with wheels. An (...) (23 years ago, 15-Jun-03, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: EGAD! (pneumatics)
|
|
(...) You are doing well Mark. You can use three voltage comparators to detect which voltage level is being output. What you need is three comparators. One for 25%, then 50%, and 75%. If 75% is on, then you'll need to gate off the 25% and 50% (...) (23 years ago, 15-Jun-03, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: EGAD! (pneumatics)
|
|
(...) Close. What I would actually be wanting is eomthing that could use the voltage level being output from a *SINGLE* RCX port to do the addressing. So for controlling up to four devices from one port, for example, would require that 25% power to (...) (23 years ago, 15-Jun-03, to lugnet.technic, lugnet.robotics)
|