To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *36224 (-10)
  Re: Interesting BrickOS Timing Results
 
(...) My thought was that the OCRA interrupt could be used as the general 1ms interrupt and the subsystem handler (which is currently using OCRB) could be called every other time from the OCRA handler by using a flag (toggled every 1ms). Actually, (...) (24 years ago, 15-Jan-03, to lugnet.robotics.rcx.legos)
 
  Re: DISTRIBUTED/PARALLEL CLUSTER for legOS through n*RCX
 
Last year I built a robot which used multiple RCXs in the way you mention. I was building a sumo wrestling battle bot, and at some point ran out of sensor ports. For my sumo bot I'd built up some small abstraction layers around the sensors and (...) (24 years ago, 15-Jan-03, to lugnet.robotics.rcx.legos)
 
  Re: DISTRIBUTED/PARALLEL CLUSTER for legOS through n*RCX
 
Just a question about this. Won't the IR airwaves will be a major bottleneck for most parallel applications? -Kekoa (24 years ago, 15-Jan-03, to lugnet.robotics.rcx.legos)
 
  Re: Interesting BrickOS Timing Results
 
OCRA and OCRB are output interrupts for the 16 bit timer. They can be programmed to fire at specific points along the timers run. So, technically, they cannot be used independently of each other. If OCRA resets the timer value back to zero, then (...) (24 years ago, 15-Jan-03, to lugnet.robotics.rcx.legos)
 
  Re: Spybotics to RCX message
 
Hey cool, Mark, this is really going to be useful! I've noticed that when MindScript generates a call to the SendRCXMessage subroutine, it always pops the calling parameters off the stack. For example, this MindScript code: SendRCXMessage(5) (...) (24 years ago, 15-Jan-03, to lugnet.robotics.spybotics)
 
  DISTRIBUTED/PARALLEL CLUSTER for legOS through n*RCX
 
Hi all. I'm taking a course on parallel/distributed operating systems. So this post attempts to find out if someone has thought, or has implemented some kind of distributed application over BrickOS/legOS (from now legOS, for this post). I know (...) (24 years ago, 15-Jan-03, to lugnet.robotics.rcx.legos)
 
  Re: I2C device for the RCX
 
(...) Well, one reason for this is that I2C doesn't need a precise clocksignal (thanks to Dick Swan for telling me, I totally forgot about it). All the timer stuff shouldn't matter for the I2C device, so there should be even higher speeds possible, (...) (24 years ago, 15-Jan-03, to lugnet.robotics)
 
  Re: Interesting BrickOS Timing Results
 
(...) Timer B is usually unused but has a lower priority than Timer A. If you do a lot of stuff in the timer A routine, this will block timer B interrupts (especially if timer B generates more interrupts than timer A). The mean thing is that those (...) (24 years ago, 15-Jan-03, to lugnet.robotics.rcx.legos)
 
  Re: RCX Motor Controller
 
(...) The RCX is equipped with MLX10402 H-bridge drivers (take a look at www.melexis.com). These drivers have two inputs to control the H-bridge: IN_1 IN_2 0 0 -> motor off 1 0 -> forward 0 1 -> backward 1 1 -> both motorpins switched to ground The (...) (24 years ago, 15-Jan-03, to lugnet.robotics)
 
  Re: Land mine robot
 
Metal detectors are subtle things. Good ones can distinguish between an aluminium ringpull and a gold coin; bad ones get confused by damp soil. The simplest and cheapest design I've seen used a PIC12C508, a hand-wound coil, a resistor and a couple (...) (24 years ago, 15-Jan-03, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR