 | | Re: I wish Lego made an "Anti-Backlash Gear"
|
|
cool idea..... (...) (26 years ago, 5-Apr-01, to lugnet.robotics)
|
| |
 | | Re: How about ideas for new elements?
|
|
(...) I think a sub group for 'modifiers' is a good idea. I haven't cut up any pieces myself, broken loads, but never sawn any up. What I will admit to is strenghtening parts, particulary universal joints. I bind the ends with sellotape as the (...) (26 years ago, 5-Apr-01, to lugnet.robotics)
|
| |
 | | Re: baffled by a part in RIS 1.5
|
|
I did'nt have the piece with me at the time I posted to lugnet, and yes Symbology is important. Increadibly, all of these mechanical aspects can be mapped out and calculated. It's just cool. (...) (26 years ago, 5-Apr-01, to lugnet.robotics.rcx)
|
| |
 | | Re: How about ideas for new elements?
|
|
(...) Nah, keep the posts in the main group as a constant source of temptation for the purists :-) I take your point about these mods really coming into play when you have a large collection of parts - when I was young and had a very limited amount (...) (26 years ago, 5-Apr-01, to lugnet.robotics)
|
| |
 | | Re: baffled by a part in RIS 1.5
|
|
(...) Using a unit of energy for torque would be very strange. You get an energy if you turn s.th. against a torque through some angle (expressed in radians, I think). Angles have no unit (or just 1), hence the units of torque and energy are equal. (...) (26 years ago, 5-Apr-01, to lugnet.robotics.rcx)
|
| |
 | | Re: I wish Lego made an "Anti-Backlash Gear"
|
|
(...) You can use those half beveled gears(with the recess) back to back as one gear, and one (maybe 2) crown gears as the gear on the other shaft. It depends on what the setup requires as of gear setup to work. Andy (...) (26 years ago, 4-Apr-01, to lugnet.robotics)
|
| |
 | | Re: I wish Lego made an "Anti-Backlash Gear"
|
|
(...) Explain 'Hmmm...' :-) I of course omitted the fact that my solution as described produces no mechanical advantage just a shaft going in the opposite direction. Of course, you can always replace the pair of gears on the second shaft with a pair (...) (26 years ago, 5-Apr-01, to lugnet.robotics, lugnet.technic)
|
| |
 | | Re: I wish Lego made an "Anti-Backlash Gear"
|
|
Hmmm... (...) (26 years ago, 5-Apr-01, to lugnet.robotics, lugnet.technic)
|
| |
 | | Re: c++, classes
|
|
Hi Michael, if you want to use a declarator list in the constructor you have to use the following syntax: /******* Implementation of the constructor ***...***/ LightSensorHead::Lig...ensorHead( const Motor::Port motorport, const Sensor::Port (...) (26 years ago, 5-Apr-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: I wish Lego made an "Anti-Backlash Gear"
|
|
(...) I was going to say this solution is easy, but then I tried it. There are only two shaft's in this example. As lego don't make don't make a 'double width gear' You'd have to use four to make it in lego. All you'd need is three normal 16 tooth (...) (26 years ago, 5-Apr-01, to lugnet.robotics, lugnet.technic)
|