To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *22064 (-10)
  Rapidly moving plastic and rubber...
 
What moves at 12 ft/sec _on_the_ground_ and is built entirely out of LEGO parts? This: (URL) (26 years ago, 1-Jun-00, to lugnet.technic, lugnet.robotics.rcx)  
 
  Major breakthrough serial wise.
 
I have been fiddling with serial interrupts with little success. Today I finally figured out that interrupts are masked in the CCR until you run the word RCX_INIT. I was blindly assuming that interrupts were generally enabled and I only had to deal (...) (26 years ago, 1-Jun-00, to lugnet.robotics.rcx.pbforth)  
 
  [min-max] command gets no respect...
 
i just rec'd my ris1.5 and am finding the the rcx will not respect the 'set abc power [min-max]' command. should i expect the motors that came supplied to vary their speed using this command or is this command reserved for other motors? (...) (26 years ago, 1-Jun-00, to lugnet.robotics)
 
  What difference between RCX 1.0 and RCX 2.0
 
Dear sirs, who could make description about RCX 1.0 and RCX 2.0 . thanks Wanshone Chiou 6/1 2000,Taiwan ___...___ pchome §K¶O¹q¤l«H½c¡A¥Ó½Ð½Ð¦Ü: (URL) (26 years ago, 1-Jun-00, to lugnet.robotics)
 
  using polarity switch as a rotation counter
 
I don't know if anyone has used this yet but I found that I can use the polarity as a raw rotation counter with four positions, 2 off and two on. if geared down with a worm gear you can get 8 rotations per turn and more, well you get the idea. just (...) (26 years ago, 1-Jun-00, to lugnet.robotics)
 
  Re: RCX 1.5 to 1.0
 
Andy Gombos wrote ... (...) The 1.0 and 1.5 firmware are identical. -- Mark Haye, mark_haye(@)tivoli(.)com IBM TSM Server Development, Tucson, AZ (26 years ago, 1-Jun-00, to lugnet.robotics)
 
  Re: XC68HC11F1B4 Pin assignments
 
in article 393601FD.1DF@hemo.net, Zele at 4n7ax@hemo.net wrote on 5/31/00 11:26 PM: (...) I found the documentation for the MC68HC11F1 series on the Motorola web site at this URL: (URL) documentation is in an 848k PDF file: (URL) picture you're (...) (26 years ago, 31-May-00, to lugnet.robotics, lugnet.robotics.handyboard)
 
  0.5 degree resolution with rotation sensor
 
Hi guys! I've been playing with a position controller and thought that could interest someone else. Since the rotation sensor has only 16 counts for 1 full turn, which means 22.5 degrees, I thought about a way to get some more precision. In order to (...) (26 years ago, 31-May-00, to lugnet.robotics)
 
  RCX 1.5 to 1.0
 
If you buy an RCX 1.5, but want a 1.0, can you just download 1.0 firmware to make it a 1.0? Thnx, Andy (26 years ago, 31-May-00, to lugnet.robotics)
 
  XC68HC11F1B4 Pin assignments
 
Hello, I have few XC68HC11F1B4 in 64-pins plastic SDIP, but can not find any data about pin assignments for this chip. Can somebody to help me with it ? Please e-mail to: 4n7ax@hemo.net Z. Ristic (26 years ago, 31-May-00, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR