 | | Re: non-linear motor speed problem
|
|
(...) Several reasons. Understand that PWM has the effect of controlling the amount of power fed to the motor, power is related to current in a quadratic (p = i^2r), and your current is related to the voltage applied and the motor parameters (...) (30 years ago, 11-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | LCD and interrupts
|
|
(...) Actually, that's not quite true. The systick interrupt always runs, and LCD writing happens as _part of_ systick. Any interrupt, by default, disables further interrupts until it's done. Systick is actually different, because it re-enables (...) (30 years ago, 11-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: 100 sensors
|
|
What's a resitor ladder? Is there a textbook or something where I can get a schematic? Is is same as a D-A converter? ---...--- ericson mar Master of Engineering Candidate Project: Mobile Robotics mar@cooper.edu (212)353-4356 Department of (...) (30 years ago, 12-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | Spike protection
|
|
Does anyone know if the motor ports on the HB are spike protected? I would like to actuate a relay from a motor port. Normally a diode across the coil kills the spike, but I was wondering if the drivers on the HB already handle that. Thanks, Terry (...) (30 years ago, 12-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | ztx614
|
|
Digikey is out of stock of the ztx614 transistor. Can anyone tell me another supplier for this transistor? Can I substitute a different transistor? If so, which one(s) would work? Thanks! .... Jim Montague (30 years ago, 12-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Spike protection
|
|
Terry, If you have the L293D or the SN754410 motor driver chips, then the diodes are present. - Prabal (...) (30 years ago, 12-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: 100 sensors
|
|
(...) A resistor ladder is simply several resistors, connected in series with a switch between each one. On the handyboard you would do something like this: VCC ---\/\/\/---\/\/\/--.../---...--- | | | | | | \ SW1 \ SW2 \ SW3 \ SW4 \ SW5 | \ \ \ \ \ (...) (30 years ago, 12-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: IR Collision avoidance
|
|
(...) My question is...in the first diagram (below) the resistance is 220 ohm ie 0.2KOhm But in the second diagram the resistances are 2.2KOhm Which is the correct one? ---...--- (...) (30 years ago, 12-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | ds1233-10
|
|
I have had trouble finding this part(DS1233-10). Does anyone know the properties of this part or an acceptable replacement? Jim Hamilton (30 years ago, 13-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | Flame detection
|
|
What are some common methods people use to detect candle flames in a room filled with flourecent and/or halogen lights? THat is, what does one use to differentiate between ambient and flame lights??? Sincerely, Yoni Garbourg << To succeed, Atificial (...) (30 years ago, 13-Mar-97, to lugnet.robotics.handyboard)
|