To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *12071 (+10)
  serial
 
Hi, I am also having some problems with serial communications. I am trying to send information back and forth between linux and the handyboard. I wrote a simple serial sender for linux and have been trying to send to the handyboard. I have two big (...) (27 years ago, 14-Jun-99, to lugnet.robotics.handyboard)
 
  RE: The ULITMATE LEGO Storage containers from Israel!!!!
 
(...) I'm in Holland and have to agree with you that these ZAG things are indeed great. Actually the ones (4) I have are a set of drawers on wheels (Roll'n Store, featured at (URL) You can also take them apart completely and reorganize the layers, (...) (27 years ago, 14-Jun-99, to lugnet.robotics)
 
  Motorized Cyberslam Cannons
 
-Has anyone come up with a good, _compact_ way to use a motor to trigger Cyberslam cannons? I'm still working on my Lego Mindstorms Ogre project, and it's got six cannons serving as the missile launchers on the back half. Space is kinda tight. -JW (...) (27 years ago, 14-Jun-99, to lugnet.robotics)
 
  Re: Anyone have any luck making a successful floating boat?
 
From: Erik Eckhardt <esquared@antispam.jps.net> (...) When I was a kid Lego boats came with a large keel piece which was quite heavy (filled with iron or lead?) and effective at putting the CoG below the water line. I don't know if the current boats (...) (27 years ago, 14-Jun-99, to lugnet.robotics)
 
  Re: Wheel Setup for the 8880
 
(...) I don't think I understand what you mean with that. Anyway, if you're interested in making independent front suspension, I have a couple of ideas here: (2 URLs) (27 years ago, 14-Jun-99, to lugnet.robotics)
 
  H-bridge
 
Hello, Does anyone know if there is a vendor that sells a H-bridge that is ready to be used for the Handy-board, instead of me having to wire up a National Semiconductor LMD18200. Thanks for your time guys. Juergen Lunkwitz Drexel University (27 years ago, 14-Jun-99, to lugnet.robotics.handyboard)
 
  Motion sensor
 
Hello all, Thank you for all of your kind help in the past. Here is another question that I hope is worthy of your time... I have a motion sensor purchased from Acroname (Eltec, I forget the part number). It works, as I had written a small program (...) (27 years ago, 14-Jun-99, to lugnet.robotics.handyboard)
 
  Re: Motorized Cyberslam Cannons
 
I have a bank of four triggered by cams on an axle. It's 12 studs wide. The axle is driven by a chain drive. I'm using a rotation sensor to control individual firing. Sorry, no digital camera, no photos. (...) (27 years ago, 14-Jun-99, to lugnet.robotics)
 
  Re: Lego Network Protocol questions
 
Ralph Hempel wrote in message <000001beb0e4$f9d0df...pro150>... (...) I'll back you up on this as well. I did some experiments using two towers connected to two different PCs, and found that I could send raw bytes from one PC to the other without (...) (27 years ago, 14-Jun-99, to lugnet.robotics.rcx.legos, lugnet.robotics)
 
  IRPD sensors
 
I have gotten some Infrared Proximity Detectors (IRPD), but no instructions for using them with the handyboard. These are set up with an infrared LED on each type of the sensor, and they are intended to give left/right/front detection. The program (...) (27 years ago, 14-Jun-99, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR