 | | Re: We need an update NOW (Was: Parts Update?)
|
|
(...) Do you really think this is a 10 minute job? If so you must really have a low opinion of the gang, then, that they would hold out on you to save a mere 10 minutes of their time. I hope that's not the case, but rather that you're just really (...) (23 years ago, 1-May-01, to lugnet.cad.dev, lugnet.cad.dev.org.ldraw)
|
| |
| | Re: We need an update NOW (Was: Parts Update?)
|
|
(...) Zipping up the parts already collected: 5 minutes Writing the disclaimer: 2 minutes Uploading zipfile and disclaimer to LDRAW.ORG: 3 minutes Catching the warm glow as the parts preview is released: Priceless. For the really big tasks there's a (...) (23 years ago, 1-May-01, to lugnet.cad.dev, lugnet.cad.dev.org.ldraw)
|
| |
| | Re: We need an update NOW (Was: Parts Update?)
|
|
(...) You can't have your cake and eat it too, Jeremy! Who do you think would be doing a significant portion (hopefully not all, but non zero) of the packaging task? ++Lar (23 years ago, 1-May-01, to lugnet.cad.dev, lugnet.cad.dev.org.ldraw)
|
| |
| | Re: We need an update NOW (Was: Parts Update?)
|
|
(...) Let's not reinvent the wheel. This process is already largely done, I would think, as part of the new parts update system now in development. The interim solution needs to be quick & easy for the implementors. Cheers, - jproat (23 years ago, 1-May-01, to lugnet.cad.dev, lugnet.cad.dev.org.ldraw)
|
| |
| | Re: We need an update NOW (Was: Parts Update?)
|
|
(...) Thank you Fredrik, for so succinctly expressing what I was feeling. I was building up a lot of frustration because I felt I had to make a loud noise in order to be heard. (...) I think the discussions should still be in the open. No consensus (...) (23 years ago, 1-May-01, to lugnet.cad.dev, lugnet.cad.dev.org.ldraw)
|
| |
| | Re: We need an update NOW (Was: Parts Update?)
|
|
(...) This would work. Just don't take Steve off of the new system -- with him working on it, it's gonna be good. Cheers, - jsproat (23 years ago, 1-May-01, to lugnet.cad.dev, lugnet.cad.dev.org.ldraw)
|
| |
| | Re: We need an update NOW (Was: Parts Update?)
|
|
"Fredrik Glöckner" <fredrik.glockner@bio.uio.no> wrote in message news:qrd1yq98itn.fsf....uio.no... (...) Its not a matter of hiding the work, see below. (...) This is the case. Newsgroup discussions get noisy - people tend to have long drawn out (...) (23 years ago, 1-May-01, to lugnet.cad.dev, lugnet.cad.dev.org.ldraw)
|
| |
| | Re: We need an update NOW (Was: Parts Update?)
|
|
"Chris Dee" <chris_w_dee@hotmail.com> wrote in message news:GCnMwn.Axw@lugnet.com... (...) Disagree. We package the parts and put a whoppin disclaimer on them. They are not official, just compiled and made easily available. We make it clear that (...) (23 years ago, 1-May-01, to lugnet.cad.dev, lugnet.cad.dev.org.ldraw)
|
| |
| | Re: We need an update NOW (Was: Parts Update?)
|
|
"Chris Dee" <chris_w_dee@hotmail.com> wrote in message news:GCnMwn.Axw@lugnet.com... (...) I've only done one part so far and I've had just 4 comments (1 on an "almost done it" post, 2 on a "done it but no optional lines yet", and 1 by private (...) (23 years ago, 1-May-01, to lugnet.cad.dev, lugnet.cad.dev.org.ldraw)
|
| |
| | Re: We need an update NOW (Was: Parts Update?)
|
|
"Tim Courtney" <tim@zacktron.com> wrote in message news:GCMuJ8.E5M@lugnet.com... (...) the (...) attached. (...) I think this needs a little modification - if the parts could be zipped separately then people could just get the ones they want, and as (...) (23 years ago, 1-May-01, to lugnet.cad.dev, lugnet.cad.dev.org.ldraw)
|
