| | Re: Influencing what parts people work on
|
|
(...) followed by silence from everyone else. Wrong group? Drop me a note if you think I should have posted this somewhere else... Thanks! The charter for cad.dat.parts didn't quite seem to fit. ++Lar (25 years ago, 3-Apr-00, to lugnet.cad.dev, lugnet.cad.dat.parts)
|
|
| | Re: My first part: 2x8 tile
|
|
Whoa, waitasecondhere.... A *TWO*-by-eight tile? From which set did you get this part? I've never seen a *two*-by-eight tile... (1x8s, yeah, sure, I've got zillions of 'em, but a *2*x8?...) Thanks, Franklin (25 years ago, 3-Apr-00, to lugnet.cad.dat.parts)
|
|
| | Re: My first part: 2x8 tile
|
|
That's a good start. Do you know its part number? (...) Should be: 0 Tile 2 x 8 (...) (25 years ago, 2-Apr-00, to lugnet.cad.dat.parts)
|
|
| | My first part: 2x8 tile [DAT]
|
|
Well, it was easy to make this. Alan 0 Plate 2 x 8 1 16 60 4 0 1 0 0 0 -1 0 0 0 1 stud4.dat 1 16 40 4 0 1 0 0 0 -1 0 0 0 1 stud4.dat 1 16 20 4 0 1 0 0 0 -1 0 0 0 1 stud4.dat 1 16 0 4 0 1 0 0 0 -1 0 0 0 1 stud4.dat 1 16 -20 4 0 1 0 0 0 -1 0 0 0 1 (...) (25 years ago, 2-Apr-00, to lugnet.cad.dat.parts)
|
|
| | Re: NEW PART: Cylinder 2 x 2 x 2/3 Inverted Dome [DAT]
|
|
Try this: 0 Cylinder 2 x 2 x 2/3 Inverted Dome 0 Name: x???.dat 0 Author: Kevin M Bane 4/02/2000 0 Un-Official Part 1 16 0 -4.5 0 6 0 0 0 0 0 0 0 6 4-4edge.dat 1 16 0 0 0 6 0 0 0 -4.5 0 0 0 6 4-4cyli.dat 1 16 0 0 0 6 0 0 0 0 0 0 0 6 4-4edge.dat 2 24 (...) (25 years ago, 2-Apr-00, to lugnet.cad.dat.parts)
|
|
| | Re: NEW PART: Cylinder 2 x 2 x 2/3 Inverted Dome [DAT]
|
|
Kevin B <kevinb01@netfocus.net> wrote in message news:FsEux1.Lp7@lugnet.com... (...) Well, I for one have a BIG problem with it! Looks like the ole "WordWrap" monster got me! Sorry folks! Let's try that one again! Kevin B 0 Cylinder 2 x 2 x 2/3 (...) (25 years ago, 2-Apr-00, to lugnet.cad.dat.parts)
|
|
| | NEW PART: Cylinder 2 x 2 x 2/3 Inverted Dome [DAT]
|
|
Well, I finally decided that the Palm Tree Trunk just made my Blue Fury look a little wierd, so I churned out this part this morning. Let me know if you have any problems or comments Kevin B 0 Cylinder 2 x 2 x 2/3 Inverted Dome 0 Name: x???.dat 0 (...) (25 years ago, 2-Apr-00, to lugnet.cad.dat.parts)
|
|
| | Re: New Part: Brick 1 x 3 with Control Panel Pattern
|
|
(...) No. From the standard file, you need to "cut out" the surface(s) where the pattern will be. If you don't, the results will be unpredictable. /Tore (25 years ago, 2-Apr-00, to lugnet.cad.dat.parts)
|
|
| | Re: PART 20283.dat Slope Brick 45 4 x 6 Double Inverted [DAT]
|
|
Yes, you're absolutely correct. How sloppy of me. :-/ (...) Here's the file with your correction: 0 @Slope Brick 45 4 x 6 Double Inverted 0 Name: 20283.dat 0 Author: James Jessiman (4854.dat) 0 Author: Modified into 20283.dat by Tore Eriksson 0 (...) (25 years ago, 2-Apr-00, to lugnet.cad.dat.parts)
|
|
| | Re: New Part: Brick 1 x 3 with Control Panel Pattern
|
|
It's the first time i open a part with a pattern. Great work But, is it possible to re-use a standard 3622, and add only the pattern ? -- Damien et Nathalie Duquennoy 26, rue du belvédère 69210 L'ARBRESLE dduquenn@club-internet.fr (URL) Dee (...) (25 years ago, 2-Apr-00, to lugnet.cad.dat.parts)
|