 | | Re: New LDraw based editor... GLIDE. Click authors required.
|
|
(...) Note also that a 1x4 brick can be attached to a 2x4 brick anywhere on about 70-80 degree angle if only attached by the end stud - its only the other studs hitting the sides that restrict it. ROSCO (20 years ago, 23-Jun-04, to lugnet.cad, lugnet.cad.dev.lcd, lugnet.cad.dat.parts)
|
| |
| | Re: New LDraw based editor... GLIDE. Click authors required.
|
|
I guess I'm thinking about this differently. It's not that the individual studs on the brick don't allow other mating angles. (IE you can place a 1 x 6 technic plate with rounded ends on any single stud at some funcky angles) It's the combination of (...) (20 years ago, 23-Jun-04, to lugnet.cad, lugnet.cad.dev.lcd, lugnet.cad.dat.parts)
|
| |
| | Re: New LDraw based editor... GLIDE. Click authors required.
|
|
(...) I really like the way the .dat format reuses geometry e.g. stud.dat. I think the clicking format should be able to do the same thing. I imagine that would be quite a bit more difficult to reuse if the clicking info was in the dat files. (...) (...) (20 years ago, 23-Jun-04, to lugnet.cad, lugnet.cad.dev.lcd, lugnet.cad.dat.parts)
|
| |
| | Re: New LDraw based editor... GLIDE. Click authors required.
|
|
(...) I do indeed think it would be undesirable. As we all know Stud.dat gets used every ware. There are a fair few instances were the clicking behaviours of two bricks would be different even though they are both referencing the same stud.dat file (...) (20 years ago, 23-Jun-04, to lugnet.cad, lugnet.cad.dev.lcd, lugnet.cad.dat.parts)
|
| |
| | Re: New LDraw based editor... GLIDE. Click authors required.
|
|
(...) I agree, but in the short term, I think seperate files may be simpler. (...) I thought so too, but the format document (way at the bottom) implies that this might be undesirable. I'm not sure I understand why, though : ( (20 years ago, 22-Jun-04, to lugnet.cad, lugnet.cad.dev.lcd, lugnet.cad.dat.parts)
|
| |
| | Re: New LDraw based editor... GLIDE. Click authors required.
|
|
(...) There's a difference between supporting POV inline (which is not controlled in the community) and supporting LCD info (which could be integrated into the DAT format). I'd like to see programs support both options - both as an external .lcd (...) (20 years ago, 22-Jun-04, to lugnet.cad, lugnet.cad.dev.lcd, lugnet.cad.dat.parts)
|
| |
| | Re: New LDraw based editor... GLIDE. Click authors required.
|
|
The it would be slick to have the LCD info in the dat file, but it might complicate issues being dicussed by the Ldraw committee : ( It seems that pov style includes aren't allowd in official files either so maybe keeping it seperate for a while (...) (20 years ago, 22-Jun-04, to lugnet.cad, lugnet.cad.dev.lcd, lugnet.cad.dat.parts)
|
| |
| | Re: New LDraw based editor... GLIDE. Click authors required.
|
|
(...) inline in a valid DAT file? Perhaps make all the lines start with a "0 LCD" before anything else? Then, when reading a DAT file, a program can recognize and parse LCD info, in addition to looking for the .lcd file. Does that make sense? Do you (...) (20 years ago, 22-Jun-04, to lugnet.cad, lugnet.cad.dev.lcd, lugnet.cad.dat.parts)
|
| |
| | Re: New LDraw based editor... GLIDE. Click authors required.
|
|
Hi Glide has been on hold now for about a month but its back in development. You can look forward to clicking bricks in about two to three weeks. Once I have the system implemented is there anyone out there who would be prepared to start writing (...) (20 years ago, 22-Jun-04, to lugnet.cad, lugnet.cad.dev.lcd, lugnet.cad.dat.parts)
|
| |
| | Re: Problem with click hinge part(s)?
|
|
(...) Yep Chris, taking into account the curves where the lugs join the brick, I'd say it's darn good now, thanks! ROSCO (20 years ago, 21-Jun-04, to lugnet.cad.dat.parts)
|
