| | Re: New Part: x716.dat - 0 Brick 2 x 4 x 1 Ring
|
|
(...) Looks nice. (...) 'Brick 2 x 4 Half Round with Cutouts' would fit in with 3063, 2577, and 30357. Alternatively, "Round Brick 4 x 4 Half with Cutouts" or "Round Brick 2 x 4 Half with Cutouts" (depending on how you look at it) could get the (...) (21 years ago, 9-Jan-04, to lugnet.cad.dat.parts)
|
|
| | New Part: x716.dat - 0 Brick 2 x 4 x 1 Ring [DAT]
|
|
At last, I lay my greedy hands on one of this rare, vintage macarony variant! I just had to LDraw it at once... A better name, anyone? 0 Brick 2 x 4 x 1 Ring 0 Name: x716.dat 0 Author: Tore Eriksson 0 Unofficial Part 0 KEYWORDS macaroni, round, (...) (21 years ago, 9-Jan-04, to lugnet.cad.dat.parts)
|
|
| | Re: Message to Paul Easter
|
|
(...) It must be because of my ISP's new email filters. Make sure your message says something like "ldraw" or "lugnet". They should make it through then. If not, I have emailed you using my backup email address. Paul (21 years ago, 6-Jan-04, to lugnet.cad.dat.parts)
|
|
| | Message to Paul Easter
|
|
Paul, I am trying to contact you using pneaster@knoxy.net but keep getting my E-mail back? Stragely enough it keeps saying user unknown and message undeliverable. Can you contact me, please? Jaco jmolen@zonnet.nl (21 years ago, 5-Jan-04, to lugnet.cad.dat.parts)
|
|
| | Re: Dinosaur parts [DAT]
|
|
(...) I done it. Only the orientation could be a question. Steve please tell me a part-number for this. CU Bernd ---...--- 0 Animal Tail Section (Middle) with Pin 0 Name: Animal_Tail.dat 0 Author: Bernd Broich 0 Unofficial Part 0 KEYWORDS Dinosaur, (...) (21 years ago, 3-Jan-04, to lugnet.cad.dat.parts, lugnet.cad)
|
|
| | Re: Dinosaur parts
|
|
(...) I began the Tail Section with Pin. CU Bernd (21 years ago, 3-Jan-04, to lugnet.cad.dat.parts)
|
|
| | Re: Dinosaur parts
|
|
(...) The tail sections are in my to-do-bucket. But there are many, many parts with higher priority... /Tore (21 years ago, 2-Jan-04, to lugnet.cad.dat.parts)
|
|
| | Re: Why is the Thickness of Liftarms changing?
|
|
(...) Indeed but... too late now :-( (...) ...but using plates on side of liftarms can be very helpful to stiffen chassis built with them. Philo (21 years ago, 2-Jan-04, to lugnet.cad.dat.parts, FTX)
|
|
| | Dinosaur parts
|
|
Hi all, is anybody working on these files? Animal Dinosaur Tail Section with Pin (URL) Dinosaur Tail Section End (URL) Dinosaur Head Small (URL) Bernd (21 years ago, 2-Jan-04, to lugnet.cad.dat.parts, lugnet.cad)
|
|
| | Re: Why is the Thickness of Liftarms changing?
|
|
(...) Thank you for this illustration. I see your point. These parts should have been originally modeled rotated 90 degrees around Z so that the liftarm "thickness" would have been the same a brick "width". I think I can safely say that I have (...) (21 years ago, 1-Jan-04, to lugnet.cad.dat.parts, FTX)
|