 | | Dragon skin for shield [DAT]
|
|
This image was just a tad too complicated for me to map out, so I 'created' it using BMP2DAT. 0 dragon.dat 0 Image converted by BMP-to-LDraw32 v1.02 4 14 0.99 0.99 0 2.64 0.99 0 2.64 1.32 0 0.99 1.32 0 4 14 0.99 1.32 0 3.3 1.32 0 3.3 1.65 0 0.99 (...) (23 years ago, 31-Aug-01, to lugnet.cad.dat.parts)
|
| |
| | Plate 4 x 4 Corner Round [DAT]
|
|
Has '30565' listed on the bottom of the actual piece. Lego's part #? Anyways, my example came out of the Star Wars model # 7106 DROID ESCAPE. Now to figure out how to do that (1/4) curved wall section.... 0 Plate 4 x 4 Corner Round 0 Author: Mark (...) (23 years ago, 31-Aug-01, to lugnet.cad.dat.parts)
|
| |
| | Re: Final version 973fett.dat
|
|
(...) *snip* Much much better than the 'green patterned' Blacktron torso I was using in my LDRAW models. Has anyone done a Darth Vader or a Boba Fett HELMET yet? (23 years ago, 31-Aug-01, to lugnet.cad.dat.parts)
|
| |
| | Re: Do these DAT parts exist?
|
|
Elliot, Try here: "(URL) this helps. ;-) Franklin (...) (23 years ago, 30-Aug-01, to lugnet.cad.dat.parts)
|
| |
| | Do these DAT parts exist?
|
|
1. Boba Fett Torso 2. Explorian Helmet If not, I'd greatly appreciate it if someone would make them. Elliot Hyde ehyde@mac.com (23 years ago, 30-Aug-01, to lugnet.cad.dat.parts)
|
| |
| | Re: brick 1x2 with one two sideways locking fingers on end.
|
|
Are you referring to *this*? "(URL) that this was posted nine months ago...) Also, it's considered "bad form" to try to encode a part that you don't actually have in-hand. Franklin (...) (23 years ago, 30-Aug-01, to lugnet.cad.dat.parts)
|
| |
| | Re: Wanted: Mindstorms parts
|
|
(...) Do you mean this one? (URL) It's one of the worst-named parts in the LDraw library. Right down there with 2880 (Hinge Train Cantenary Holder) and 2433 (Lever Control). Steve (23 years ago, 27-Aug-01, to lugnet.cad.dat.parts)
|
| |
| | Re: Anybody up to the lego soccer ball?
|
|
(...) There's one at (URL) worked on this awhile ago, probably should submit it as a "Needs Work" part - the borders between the white areas are just lines, they should be grooves. And there are no conditional lines between the facets. I thought (...) (23 years ago, 27-Aug-01, to lugnet.cad.dat.parts)
|
| |
| | Slope Brick 45 2 x 1 Without Center Stud [DAT]
|
|
I had the need for a Slope Brick 45 2 x 1 Without Center Stud in a model, so I created it by removing the center stud. This is rather simple, but I thought I'd post it anyway... What would be the correct partnumber? I have named it 3040b. 0 Slope (...) (23 years ago, 27-Aug-01, to lugnet.cad.dat.parts)
|
| |
| | brick 1x2 with one one sideway locking fingers on end. [DAT]
|
|
Here is the piece's counterpart also available in set 3750. 0 Hinge Brick 1 x 2 Locking with 1 Sideways Finger On End 0 Name: 30364.dat 0 Author: Mark Kennedy 0 based on 30364.dat by John VanZwieten 1 16 30 9 0 0 0 -1 -1 0.00 0 0.00 1 0 s/swh2.dat 1 (...) (23 years ago, 27-Aug-01, to lugnet.cad.dat.parts)
|
