 | | Re: MLCAD 3D View question Please HELP!!
|
|
(...) we'll have to wait for mike lachman to give a definative on this, but i believe there is currently *not* a way to alter the 3D viewing angle... many of us have requested the ability to alter the viewing angles freely, and even same custom (...) (25 years ago, 3-Dec-99, to lugnet.cad)
|
| |
| | MLCAD 3D View question Please HELP!!
|
|
Hi all, Concerning MLCAD's 3D view... is there any way to view other sides in 3D?? on my MLCAD... the 3D view shows from Front to the back on the "left side of the model (spaceship) is there any way to switch the 3D view so that I could see the back (...) (25 years ago, 3-Dec-99, to lugnet.cad)
|
| |
| | Re: Partsref is Moving to LUGNET
|
|
(...) lugnet.general? lugnet.helpwanted? The current problem is that there aren't that many published inventories for current sets. So you need to hook up to someone who is A-R enough to inventory everything themselves,. Steve (25 years ago, 3-Dec-99, to lugnet.cad.dev, lugnet.db.brictionary)
|
| |
| | Re: Partsref is Moving to LUGNET
|
|
(...) I'm going to need to keep a vanilla installation, just for partsref generation. It's too tempting to make minor edits to part files in my regular installation. And, if I'm going to have two copies of LDraw, I'd rather have "working" and (...) (25 years ago, 3-Dec-99, to lugnet.cad.dev, lugnet.db.brictionary, lugnet.cad.ray)
|
| |
| | Re: Partsref is Moving to LUGNET
|
|
[should've snipped the ng list, but I didn't--couldn't decide which to keep/exclude] (...) So, as both the new Keeper of the LDraw Library and the Keeper of the Partsref Pages, I could build a make, and apply it everytime I get new candidate files (...) (25 years ago, 3-Dec-99, to lugnet.cad.dev, lugnet.db.brictionary, lugnet.cad.ray)
|
| |
| | Re: New part: Plate 6 x 6 x 2/3 Cross with Dome - 30303.dat
|
|
(...) Nice job, it looks good. While looking at the new tubes, I noticed another problem. There are no edges on the curved surfaces! You can see this if you look at the part in LDLite with wireframe and rotation turned on. The regular studs, and the (...) (25 years ago, 3-Dec-99, to lugnet.cad.dat.parts)
|
| |
| | Re: track, 9 volt. mockup, measurement request of this part
|
|
Hello all, I've noticed there is a mockup file being passed around, wich proofs there is a definite need for an official part #2865 - Train Track 9V Straight. Hmm.. it's a nice difficult one. Would you please answer the following questions: 1. Has (...) (25 years ago, 3-Dec-99, to lugnet.cad.dat.parts)
|
| |
| | Re: help - part number wanted
|
|
(...) My Guess is that he is refering to the little grey part that goes over the axle joiner piece. -- Jonathan Wilson wilsonj@xoommail.com (URL) (25 years ago, 3-Dec-99, to lugnet.cad.dat.parts, lugnet.db.inv)
|
| |
| | Re: Line in the Sand
|
|
(...) at first i misread that as: (...) and thought to myself "wow, Steve's in a really cynical mood".. hehe.. guess i'm just projecting my own cynicism... J (25 years ago, 3-Dec-99, to lugnet.cad.dev)
|
| |
| | Re: help - part number wanted
|
|
Axel Poqué wrote in message ... (...) Shuttle". (...) I believe that the part you are looking at is part number 6631. In my inventory I describe it as: 6631 - Plate, 2x6, with 1x2 "T" Hole in Center and One Deceding 1/2 Two of these plates are used (...) (25 years ago, 3-Dec-99, to lugnet.cad.dat.parts, lugnet.db.inv)
|
