 | | Re: Missing primitives after part update.
|
|
(...) Hello again, No, I had not installed ldraw027.exe. My version of Ldraw came from a CD, along with other tools like MLCAD and POV-Ray. I have tried the part update on two separate computers, with the same Missing Primitives result. I will try (...) (18 years ago, 1-Dec-06, to lugnet.cad.dat.parts.primitives)
|
| |
| | Re: Missing primitives after part update.
|
|
(...) Did you install ldraw027.exe? Not having done that seems to me to be the most likely cause of your problem. You have to install ldraw027 prior to installing any updates (including the complete update). This should change once the library gets (...) (18 years ago, 30-Nov-06, to lugnet.cad.dat.parts.primitives)
|
| |
| | Re: Missing primitives after part update.
|
|
(...) Hi Michael, It is pretty hard for us to diagnose this without a lot of details of mising files. Before we go down that road, I would recommend you try again, or start over with empty ldraw/parts ldraw/parts/s and ldraw/p folders (directories). (...) (18 years ago, 30-Nov-06, to lugnet.cad.dat.parts.primitives)
|
| |
| | Missing primitives after part update.
|
|
Hello, This is my first post, so please bear with me if I screw up. I have downloaded the Ldraw part updates, and installed them according to the instructions posted at the update site. My problem is that, every time I opened a parts folder in (...) (18 years ago, 30-Nov-06, to lugnet.cad.dat.parts.primitives)
|
| |
| | Re:SketchUp: x93 Monkey Wrench
|
|
(...) I've been looking for a part to try my SketchUp to LDraw exporter, so I made this model. It's more a generic pipe wrench than actually based on the real part. Not sure what to scale it to, either. Maybe you can tweak it. SketchUp model : (URL) (...) (18 years ago, 29-Nov-06, to lugnet.cad)
|
| |
| | Re: Lego factory sets / building instructions
|
|
Paul S. D'Urbano wrote: [...] (...) [...] (...) Paul, It would be great if the models were built and commented on. I know the few models that I submitted are buildable, but that kid of defeats the real purpose of Factory... I mean really, if I (...) (18 years ago, 29-Nov-06, to lugnet.trains, lugnet.cad.ldd)
|
| |
| | Has anyone made the x93 Monkey Wrench
|
|
(URL) need it to finish the AT-AT. (18 years ago, 29-Nov-06, to lugnet.cad)
|
| |
| | Re: LSynth electric cable cross section oriention problem
|
|
(...) Me too! Kevin (18 years ago, 27-Nov-06, to lugnet.cad.dev)
|
| |
| | Re: Tyre 30.4x14
|
|
ludo soete schrieb: (...) On Peeron this part has the number: 30391. But it is not on the parts tracker. mikeheide (18 years ago, 26-Nov-06, to lugnet.cad.dat.parts)
|
| |
| | Re: LSynth electric cable cross section oriention problem
|
|
(...) Hi Kevin, Another possibility to investigate is to change the up vector in inverse proportion to the bezier curve change. That would mean it would twist less where there's a sharper bend, and would possibly end up looking more authentic. But (...) (18 years ago, 26-Nov-06, to lugnet.cad.dev)
|
| |
| | Re: LSynth electric cable cross section oriention problem
|
|
(...) Leo, In case you didn't get this far, I solved the above problem and can now control twist all through a cable segment from start point to end point. I calculate the up vector for the start of segment, and the up vector for the end of segment. (...) (18 years ago, 26-Nov-06, to lugnet.cad.dev)
|
| |
| | LDAO problem
|
|
i guess this would be the correct spot for the message. i have a install problem with LDAO. i install it, and when i stat it i get error 76 , path not found. (18 years ago, 26-Nov-06, to lugnet.cad.dev)
|
| |
| | Tyre 30.4x14 VR
|
|
Hi all, Anyone having a mocup from the following tyre? (...) Any help with a mocup is apreciated. Regards, Ludo (18 years ago, 25-Nov-06, to lugnet.cad.dat.parts, FTX)
|
| |
| | Tyre 30.4x14
|
|
Hi all, Anyone having a mocup from the following tyre? (URL) I noticed the request for it abouth 4 years ago, and it is still not apearing on the LDRAW site - unofficial parts. Any help with a mocup is apreciated. Regards, Ludo (18 years ago, 25-Nov-06, to lugnet.cad.dat.parts, FTX)
|
| |
| | Re: DAT file for 4531-9V Switches
|
|
(...) on LDraw's parts tracker searching for 4531. Thanks in advance for any (...) tracking it down. Hi, Take here a look for a mocup of the 9V RC points (100% plastic) by Thomas Burger: (URL) They are build after my mocup for the 9V point (with (...) (18 years ago, 25-Nov-06, to lugnet.cad.dat.parts, FTX)
|
| |
| | Re: Lego factory sets / building instructions
|
|
(...) Hi Ville, Unfortunately, there's no simple way to get the typical LEGO instructions experience with Factory. Often LDD's automatic instruction steps aren't well organized and sometimes impossible to follow. It's better if the model author (...) (18 years ago, 25-Nov-06, to lugnet.trains, lugnet.cad.ldd)
|
| |
| | Re: LSynth electric cable cross section oriention problem
|
|
I've got up/side/front vector stuff working now, so that I can control the orientation of cross sections of electrical cables at the start of a segment defined by two constraints. My issue now is that I don't know how to force the twist so that the (...) (18 years ago, 24-Nov-06, to lugnet.cad.dev)
|
| |
| | Re: bend thingie creator.
|
|
(...) Let me check my archive of LDraw related programs and if I have it I'll email it to you. -Orion (18 years ago, 24-Nov-06, to lugnet.cad.dev)
|
| |
| | LSynth electric cable cross section oriention problem
|
|
Hi, I've got a reworked version of LSynth with a major problem... I cannot figure out how to control the twist of the cross section. I use bezier curve to created the nicely curved set of points, and compress it by tossing out points until the angle (...) (18 years ago, 24-Nov-06, to lugnet.cad.dev)
|
| |
| | Re: bend thingie creator.
|
|
(...) Koen, I tried to email you using your address, and I tried to download your bendie thingy creator. It is gone. Does anyone have a copy of this so I can play with it? Kevin (18 years ago, 24-Nov-06, to lugnet.cad.dev)
|
