 | | Re: MOTM voting for February
|
|
"Steve Bliss" <steve.bliss@home.com> wrote in message news:a0p07ts361v0md6...4ax.com... (...) Yeah...I thought of that. Different people see it different ways - I started MOTM to showcase a good 3D rendering on the front page, to display potential (...) (24 years ago, 25-Jan-01, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: Double side 8 pin plate?
|
|
(...) Nope, LEGO doesn't do those. Steve (24 years ago, 25-Jan-01, to lugnet.cad.dat.parts)
|
| |
| | Re: MOTM voting for February
|
|
(...) That's a nice quote to point out the different POV's between the people running a contest and the people entering the contest. Steve (24 years ago, 25-Jan-01, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: DAT to GIF/JPG/EPS
|
|
Don: (...) Yes. The horse was double size and the cow and the reindeer were scaled up four times. (...) Please do. Play well, Jacob PS: Has anybody looked into writing a direct DAT/MPD to Postscript renderer? -- No .sig today either. (24 years ago, 25-Jan-01, to lugnet.cad)
|
| |
| | Re: L3P v1.3 20010120
|
|
Almost sounds like a metaphor. "Infinite Focus". If u get it, u get it. :) Mike (...) (24 years ago, 25-Jan-01, to lugnet.cad, lugnet.cad.ray)
|
| |
| | Re: MOTM voting for February
|
|
"Brad Hamilton" <bhamilto1@home.com> wrote in message news:G7pAup.B5u@lugnet.com... (...) Same here! I just have to quit gawking and think 'what will look the best on the front page?' because that's the point of the contest :) -Tim (24 years ago, 25-Jan-01, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: MOTM voting for February
|
|
There is an excellent selection this month! It took me about 10 minutes to decide on my vote. Tim Courtney <tim@zacktron.com> wrote in message news:G7orCs.7oH@lugnet.com... (...) news:G7oMqH.GtD@lugnet.com... (...) I've (...) for my (...) (24 years ago, 25-Jan-01, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: Torus primitive discussion. was( Updated Primitive - 1-8t0102 1/8 torus) [DAT]
|
|
Sorry about taking so long to reply to this message. I have been working on trying to make a few of these torii mentioned below. (...) That is what I meant. :-) (...) If we worked with the method used for the rings and similar existing primitives, I (...) (24 years ago, 25-Jan-01, to lugnet.cad.dat.parts.primitives)
|
| |
| | Re: New Part In Progress: Brick 1x4 with Studs Hollow on side
|
|
Xcalabur <Xcalabur@rocketmail.com> wrote in message > (...) grey). (...) It was also in the UCS X-Wing Gary (24 years ago, 25-Jan-01, to lugnet.cad)
|
| |
| | Re: New Part In Progress: Brick 1x4 with Studs Hollow on side
|
|
(...) That was an error on my behalf... I forgot to mention that the set is still on its way to my house, so i am working from a picture in a magazine that shows the set at just the right angle that the part is visible. Sence i could only see 1 side (...) (24 years ago, 25-Jan-01, to lugnet.cad)
|
