Subject:
|
Re: Have you ever warped or broken parts?
|
Newsgroups:
|
lugnet.build
|
Date:
|
Fri, 31 Mar 2000 08:04:34 GMT
|
Highlighted:
|
(details)
|
Viewed:
|
2280 times
|
| |
|
|
In lugnet.build, John J. Ladasky, Jr. writes:
> Hi there,
>
> I've started to construct things I would never imagined • building as a kid --
> things that might strain or even break parts. I've • seen some examples of these
> types of building on various AFOL web pages, and • perhaps so have you.
>
> For example, I've built a 45-degree, 7-stud brick wall • that runs across the
> diagonal described by going five studs over and five • down. Several of the
> standard Lego octagonal plates have a 5 X 5 cutout at • the edge, such as...
>
> http://www.lugnet.com/cad/ldraw/parts/ref/search.cgi?q= • 6106
>
> ...and this is a nice way to make a wall that covers • that space. I've found
> that Ed Boxer built this same wall for his Crown • Cathedral model.
>
> http://www.geocities.com/~edboxer/crown.html
>
> We both seem happy enough with it. I've also built a • 14-stud long wall that
> spans the space covered by going ten studs over and ten • studs down. What's the
> big deal? Well, the math says that we have to be • stretching the parts to make
> these constructions work. The actual distance between • a point (0,0) and point
> (5,5) is the square root of 50, which is not seven. • It's about 7.071. That
> means that the bricks used to cover that diagonal must • be stretching, though by
> just a bit. The 14-stud wall should actually be 14.142 • studs long.
>
> I know it's possible to warp a plate -- I have a warped • 4 X 6 plate from some
> used parts I inherited. I have no idea how it got that • way.
>
> Moving on to potentially more serious consequences: • I've started to build models
> that put quite a bit of weight on hinge bricks, • turntables, and hinge plates.
> In one case, I have two plates, tilted somewhat to form • a dihedral angle, that
> meet on a knife-edge. To be sure, it's a fairly long • knife-edge, but the model
> is heavy.
>
> Eric Harshbarger described destroying some parts when • he was experimenting with
> his grandfather clock.
>
> http://www.ericharshbarger.org/lego/clock.html
>
> He describes breaking the chain parts, which is not • really so surprising. I'm
> really more interested in the kinds of things that • resulted in, for example, a
> broken gear, and a Technic axle getting twisted to the • point of unusability:
>
> http://www.ericharshbarger.org/cgi-bin/photo.cgi?clock_ • 4.jpg+lego/images/clock
>
> How far can you push Lego go before it begs for mercy? • Share your war stories!
>
> --
> John J. Ladasky Jr., Ph.D.
> Department of Structural Biology
> Stanford University Medical Center
> Stanford, CA 94305
here's one for the record books : lego death by
photography! the last image on the craigo-lego page of
my site :
http://community-2.webtv.net/anonymouseye/craigolego/
... was taken after a long night of scanning on the un-air-conditioned
third floor of a building in macon, ga in 90 degree july heat. the weird
lighting effect was achieved by shining a 75 watt bulb directly into the
scanner behind the models, the scanner glass was pretty hot after spending
a few hours making other images and combined with everything else, melted
half a 1x3 brown plate and half of the black hinge in the orange dragonfly.
the trans orange grille tile which was connected to the melted end of the
1x3 was unharmed. i still have the half melted 1x3, but lost the hinge
somewhere.
later ~ craig~
|
|
Message is in Reply To:
 | | Have you ever warped or broken parts?
|
| Hi there, I've started to construct things I would never imagined building as a kid -- things that might strain or even break parts. I've seen some examples of these types of building on various AFOL web pages, and perhaps so have you. For example, (...) (25 years ago, 31-Mar-00, to lugnet.build)
|
2 Messages in This Thread:
 
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|
