|
|
 | | Re: Lego "pegging" disks
|
| (...) I still have a lot of my Lego parts from 60s and 70s (some pictures of them at my site), but I'm pretty sure the first gears were the ones mentioned by Ralph. The largest was yellow, the medium one blue and the smaller red. Axles were white (...) (27 years ago, 13-May-99, to lugnet.robotics, lugnet.build)
| | | | | Re: Flatbeds trucks and train M.O.W. vehicles
|
| (...) could get with the lab's digital camera for my model photographs. Thanks for posting that you added images to your web site. later, James Mathis (27 years ago, 13-May-99, to lugnet.build, lugnet.trains)
| | | | | Re: Just got back from...DEKA...Auckland, New Zealand
|
| Ben Pegler wrote in message ... (...) DEKA (...) demonstration of (...) it (...) in (...) was (...) (There (...) after (...) behind (...) The only sets I've seen here in Wellington (Moore Wilsons's Tory St) are: (and to be honest I've only been to (...) (27 years ago, 13-May-99, to lugnet.starwars)
| | | | | Re: Sith Infiltrator
|
| (...) Although Micro Machines claims to be "the only scale minature", I have yet to see a Micro Machines car that is actually to scale. The are always much too high and much too short. --Bram (27 years ago, 13-May-99, to lugnet.starwars)
| | | | | SW parts wanted in LDraw
|
| Hey all, I am looking for a few of the new Star Wars parts for my next LDraw model. For at least one of them, I know it has been done but I can't find it. 30360 - engine cowling piece from X-Wing, etc. (I'm sure this one is already done) 30373 - (...) (27 years ago, 13-May-99, to lugnet.cad)
| | | | | Re: Un-Ofiicial Primitive: 1-4ring10.dat
|
| (...) Hmm, Didn't think about this... No problem. --Karim (27 years ago, 13-May-99, to lugnet.cad.dat.parts)
| | | | | Re: firmdl question
|
| (...) I believe the units are tens of firmware bytes downloaded already. Oh, to point out the obvious, this is a ROM thing, not a firmdl thing. -Kekoa (27 years ago, 13-May-99, to lugnet.robotics.rcx.legos)
| | | | | Re: Rom sensor read routine
|
| (...) The current LegOS model really hammers the sensors, almost to the point of oversampling them. It only takes a short while (less than 0.1 ms, I think) to sample all four sensors; I think LegOS samples the next sensor immediately after finishing (...) (27 years ago, 13-May-99, to lugnet.robotics.rcx.legos)
| | | | | Mark is Back!
|
| Hi all, Well I've got a new job at Broadvision, and a new email address. Its: mbenz@broadvision.com. Hope to hear from you, and see you on the 22nd! Does anyone have suggestions for the "meeting" agenda? Like: Setup 11-11:30 Yak & Lunch 11:30-2 Swap (...) (27 years ago, 13-May-99, to lugnet.loc.us.ca.sf)
| | | | | Re: lego pov ray need help (barney StYle)
|
| (...) Hey Tom, POV-Ray is available at: (URL) would probably recommend also getting Lars Hassing's L3P, which will convert LDraw files into POV-Ray scene files, at: (URL) - jsproat (27 years ago, 13-May-99, to lugnet.cad)
|
Skipped 4 messages in
groups
lugnet.admin.general, lugnet.off-topic.debate, lugnet.off-topic.fun, lugnet.off-topic.pun (Skip-filter settings)
|
